Video

Do you need to drain the oil first to remove the sensor?

👍👍👍👍

Thank you, just changed the plugs using your video. The car is running now like new. Thanks again.

Awesome thanks but don't need to remove nut . Only the cap needs to be removed.

What's the name of the tool he used to pull the cb axle out?

thanks bro, just did mine 2012 mazda5

2 comments: First, I used Amazon description: 580mAh 3.7v LiPo Battery Replacement for Jabra Evolve 75 Bluetooth Headset, Evolve 75 UC Battery,Evolve 75 SE Battery Replacement,AHB572535PST Battery Upgarde Brand: AOLIKES This battery did not require any connector modification, it was completely plug and play for my unit. Second, the tab where the first T4 screw is removed, can pivot and rotate 180, according to gravity, such that the tab is not available upon reassembly, so keep an eye on that tab, and make sure the hole for the T4 is pointed UP when you reassemble the left earpiece. Thanks for the video.

This might be the most complicated to open car.

An addendum to this problem. After replacing the roller I noticed the roller would fall out of the track. The track on my car was moving down as the door slid back. The reason was the nut was loose and allowed track movement and the sliding roller was falling off. So when you closed the door it pushed on the rubber. So I had to unsnap the plastic inside the car to reach and tighten that nut so the track would stay in place, solid. The door worked as new after that with tight track and a new roller.

Awesome video . helped me contributed 1 less item to e-waste.

i recognize those crappy tire screwdrivers

Circuit design usually employ resistors in parallel with capacitors to drain them almost immediately but that is a good practice when removing airbag just in case.

Which Screw Driver you have used to open to screw.? Any link for good screw driver which I can get from Amazon.?

Thank you. I can confirm that this fixes a sticky door. My rollers were not obviously broken like yours, but the door was extremely difficult to close. After replacement, it's smooth like butter.

05:27 best part

I replaced my blend door actuator, but now my ac wont turn on. The ac light blinks.

Hi! I watched your CZcams channel and your content is very good. I am a big fan of your. I have proven strategies for optimizing CZcams content to rank higher in search results. Let's work together to optimize your video titles, descriptions, and tags for maximum visibility. Thanks

Thank you for this video it has solved a great problem for me!

used this guide today on a 2014 ... thanks worked like a charm

Excellent video! That seemed like a lot of work (for me) but watching you do it step by step makes it a possibility for me. Thanks!

will this fix the issue with one side (the battery side) not working.

Thank you! You just saved another headset.

Good job 👍🏻

Thank you! Great video, so helpful.

Does Mazda specify the torque for this anywhere? On my NKG plugs it illustrates the torque with the amount of turn you should do, but I rather had a number.

thank you! btw, i use these headsets for 4 years and i replace them every 2 years because mic stops working: battery has never died but mics die regularly due to movements up and down and cable breaks

great video, our car has this problem, will take to dealer tomorrow

Why not remove the booth easier

Procedure for Voyager V4220 is very similar to this, but the tiny battery is in the same side of the headset as the microphone, micro USB port, etc. The battery is different to the example in this video as it is has the code 1ICP4/25/38 (25 x 38 mm, I believe), and has 3 wires (red, white, black) instead of 2. Looks like the white wire could be related to battery temp monitoring, or validating that the battery is supported by the device.

Thanks so much for your video. My speaker had stopped working on the battery side and I had no clue how to get inside to take a look. It was a broken wire, soldered in a replacement, all back together and working. You've saved me the cost of a replacement.

Thanks for the video. Just replaced the battery on Jabra 75 which was completely broken. Now good as new, and the battery I ordered had the correct connector. Thank you!

My air blows cold but after a few minutes of startup, the air seems to get restricted at the vents and then blow behind the dash (sounds like defrost but I don’t feel anything up there). My set up is exactly like this one, no dual zone or anything, so which one needs replacing? Another video says my problem is the mode actuator and that it is on the driver side but your description here makes it seem like the one behind the radio.

Thank you! My 2003 CRV starts again. I struggled for an hour with the small screw on the back of the ignition switch until I ran to the hardware store and got a long, thin, phillips head screwdriver. Came right out.

You can also calculate it. P = U * I which leads to Wh = V * Ah -> Ah = 1,3/3,7= 0,3514 Ah = 351 mAh

Thank you! Great job. You told me what I need to know without a lot of extra talking. I only wish I had replaced this part before I broke the handle trying to slam the door harder and harder. Sigh.

You do not need to remove the nut simply pull back on the arm and it gives you plenty of room to remove the blade

what is the size of the heat shrink sleeve? what dia should we use?

Thanks ;) Battery swapped. Everything works.

А при замене модуля надо ли снять клеммы с аккумулятора

Thank you so much. I have yhe sme washer with same problem!! This was a big help

There is no need to remove the blade arm assembly from the car. Once the plastic clip/cover over the nut is removed, you can pull the blade assembly away from the window and the blade can easily be rotated out of the arm.

Awesome, thank you!

That 8mm deep socket threw me for a loop! Thanks for specifying the size!

Nice work 🙏thanku ❤

Thanks for sharing, you made that look so easy.

Thanks easy install. I could reach the camera from underneath the bumper.

Nice one mine would benefit from a new battery .

Fixed mine with a piece of rubber tubing which I inserted over the piece of rod to reestablish the proper contact. No new parts, no visit to the dealers, took less than 10 min. It’s been months and working fine.

What’s the best radio can anyone give me the name on this radio thanks 😊