Video

You all are selling this windshield kit as fitting a Club Car Onward and Precedent. IT DOES NOT FIT ONWARD. Though it fastens properly it leaves a huge gap at the seal. Do us all a favor and don't advertise what doesn't fit. Also the quality was crap. Seal is cheap garbage and the windshield has scratches due to poor packaging. Noticed the RHOX website is no longer valid. Wonder why??

Looks easy if you already have a wiring harness from a previous install. But what if you have to wire one that didn't have that already? The 2017 EZ Go RXV does not come with brake lights as standard equipment which is crazy if it comes with lights, then brake light should be a priority, not head or tail lights!

Question in going to redo my seats club car precedent, I’m using suede material will these heaters will work? I want to install on top and bottom seats. Thanks

You talk about grit off plastic but don’t show that step. That’s the most important detail

Thanks for the video! Can you provide information on your headlights? They look really nice I'd like to get these for my RXV!

Is the LGT-T3 kit compatible with the LGT-307L headlights?

Will it drain my battery if i connect it to the battery without swich

Will it work on both the front and back lights on a 2010 RXV ezgo

Very well done instructional video!

Is there a way to reinstall the sweat basket plastic grill? If not, is there an accessory sweater basket grill that can be installed?

After installation on a 2017 EZGO TXT, the horn will not shut off. Bad switch in the kit?

Rhox , Best video's for anything clubcar, I have this same kit , same cart , easy peasy with their videos ,I like to go into the project of what tools I need and this professional instructor takes you through the process step by step, Thanks RHOX

Perfect Ty. Will be installing a light kit on my 2109 Yamaha golf cart and didn’t like the pad you attach to the foot pedal. This is much better. Will look at other videos you have as well

My accent lights are not working either after connecting the harnesses. Update, this is fixed. Changed the a b connector.

Make sure you use lock washers and Loctite my top rattled loose and blew off my golf cart because the golf cart company did not use lock washers or Loctite trust me this is key do not make the same mistake I experienced

I noticed your transaxle has a welded on plate to keep it from spinning in the u-bolts. Mine doesn't. I am about to install one of your kits to my 2016 rxv. Did you guys make that modification to the axle? I Recently had my axle spin in the bolts and break several electical connections. So dont want that to happen again

My 9 pin connector is female and so is the harness I purchased . They don’t connect together. Do they make a male male connector for my cart . Ezgo rxv which has all the lights and turn signals but no turn lever

Helpful.....BUT, it sure would have been nice if you told us WHICH WAY to turn the inside part in order to decrease the toe-in

Wish it was tall enough to protect the headlights. Probably return mine for that very reason. Whats the 2 holes on the top bracket for?

great video , I see the kit number '548E' so i looked it up and the kit on amazone does not show the parts for the rear end, I watched this and see you are installing on a gas cart . You need to make it more clear that If instlled on a electric cart you do not need real spring adptors just move the rear spring ontop of the real axle .. thanks I will be getting the 548e .

Forgot the brake connector

What size is the Alan key for the 3/8 socket? Thanks

Would this fit a DS?

In this configuration will the lights still go dim when the throttle is applied?

Can i add this with a 6" a arm lift

I have the brake pad on the brake pedal, which use 2 wires. Will this product work on any light system that supports brakes?

What size bit

Your lift doesn't fit a electric rxv on the rear

Can you control the accent lights independently from the turn signal switch? There is a single wire plug in the LGT-401L wire harness that says accent light control from turn signal switch but I see no where to plug this into the LGT-132A wire harness.

Will this work on a Bintelli Beyond?

Is this a swamp ac?

I have a 2018 Yamaha drive2 cart that has a Rhox LGT-401L light kit installed. I would like to add the LGT-132A turn signal kit to it. This cart already has a horn and and accessory plugs so I don’t really want to buy the LGT-T3 kit. I see in the Rhox garage videos they talk about a LGT-590 jumper to replace the on/off switch, is this required? I do not see it listed anywhere on your site to order this part number.

what nine pin plugs does the jumper wire go to. Thank you.

Question: WRT the shackle plate, should that be loose (swinging freely) or tight? I just replaced my rear springs and replaced the bushings on the high side of the shackle plate (since I assume they rotted away like all the others). Now that they're in, though, the plate is rather tight and no longer swings. Do I need to loosen the bolts?

Quick and painless, super helpful video! Thank you!

The video shows a buff color top but the website only shows black? Is the buff nolonger available?

Will it fit a 26” tire?

Does the LGT-132A Kit come with the long black plastic wire cover for the steering column?

Link for bumper guard ?

How do you reuse the plastic sweater peace when you install the backrest

Great video and to the point. Wonderful job and thanks for the help sir

Are these coolers and brackets still available?

I have a plastic trim piece going down at back seat - what do I use ?

Ahhhh Haaaa. A 16 to 12 V reducer. No wonder the lacking manual showed plugging into the middle of the battery pack. Manual is shit.

Why didn’t you let people see the finished product?

This lift was really easy to put on, thanks for the tutorial it was a good reference!!

So after making adjustments how do you center up the steering wheel of it’s not center??

Thanks for the video 😊

Question. Is there supposed to be continuity between the white and black 120v tabs on the board Ive replaced the board and when plugged in it trips the outlet breaker. I checked the board and there is contunuity between the white wire tab and the black withe tab for the power cord. Thanks!

Do you have anything on how to adjust the beam once the housings are installed?