Video

Helpful, generally Shimano brake system is very easy and simple to bleed. But anyway thank you👍

There's another method called "gravity method", which doesn't require a syringe, just the end hose of the syringe and of course the reservoir attached to the brake lever, do you think that gravity method will work?

How bout an update? How do you like it as single speed?

Great Instructional Video! I would only add - Try to avoid allowing the air bubble to get into your brake hydraulics because they can sometimes be difficult to remove and they will cause your brakes to feel "spongy".

how about bikepacking ? easy to 32+22 with load ?

Thanks! I needed to understand what that valve was next to the rubber grommet.

the serra hub is definitely the weakest link on this bike. When mine got trashed I tried to just replace the freehub but it was jammed on there good! my 14mm couldn't get it to budge at all. I even hit it with my impact wrench (a milwaukee stubby 3/8 rated for 350ft lbs) and it couldn't get it off. I ended up upgrading it to a spank hex-drive and I love the high engagement. such a worthwhile upgrade. Although I'm not sure if I like the buzz, it has it's benefits but I think I'd prefer a silent hub like the Onyx.

I heard online that cardboard masks mold over time, I'm going to put some fabric on the inside to stop that I suggest you do that too but great mask :)

vehicle centipede

That's crazy

LoL

how many ml are you injecting into it ?

Tbh its cool,it looks like Minecraft bonnie

The 32 Tooth Cog will work with Endless Mountain Bikes ?

Wow that’s a nice rainbow! And your sons Bonnie mask was awesome!

I know that this is a few years too late, but DAMN that kid did such a good job

Minecraft version

Excellent video!

Was the funnel a m5 or m7 thread?

Little dude should be hired for the fnaf movie costume department

Actually, your guide is incorrect as it is missing 2 essential steps. 1. Before inserting the bleeding block, you would push pistons back into the body while the cup is already installed on a lever (system open on the top). 2. Your caliper will be with bubbles unless you push back at least 1/2 of the cup back with a lever main cylinder. You can seal the bottom screw only after that part. You can learn the correct process at the parktool or shimano manuals.

Good video. Does Salsa offer a rear drive side drop out without the derailleur hanger?

It's nice but mines kinda better I'll give you link from where I got the base and rest in this comment

It’s good but why does it look like it’s made to be in Minecraft?

damn that will kid is crazy

looks like he found a nice shady spot out of the heat! (is it hot there right now?)

thanks for the video

that guy in the white shirt is insane at shooting, for sure hit bullseye every time

We should show more support for this YT channel

KID

Minecraft fnaf

Omg make a square torso lol

your so creative keep it up, you should make william afton (spring trap)

Your vid is the most direct I could find on CZcams, thanks bud

Stoped

Boo

That’s sick!

I made a really cook paper withered bonnie

this mans father is more supportive than my father ever was lol

Wow a Box on his head that took 10 minutes to make.

I got the 666 like 😳

You should make the full cost

👍👍👍

my heart

It looks like from Minecraft

I made spring trap and mangle out of paper I can still wear it on my head it does not look as good but I’m a starter

Hello, I set up per the video and did the half to 3/4 turn on the screw. Don’t know why, but when i tried this method, the fluid would not go up through the system. Almost like it was plugged. When I reversed the process (ie drain out into a plastic bag), there was flow. Any reason why there was no flow when using syringe at break? Tnx in advance!

nice hope he may express his fandom and maybe a great cosplayer!

that sucks

noob