- 16
- 10 164
Cromag Meditations
Registrace 23. 10. 2022
Video
mini truck 4 link installed!
zhlédnutí 374Před 10 měsíci
installed a cheap 4 link kit and welded axle brackets and began painting the axle assembly
acura rsx coilovers on mini truck
zhlédnutí 66Před rokem
used 1/4" plate to make coilover mounts for the rear custom chassis for isuzu pickup
diy c notch and frame rails about halfway done
zhlédnutí 118Před rokem
Got the frame rails on and crossmembers welded on. Link bars and mounts next along with recycled miata coilovers
minitruck rear frame swap with c notch diy
zhlédnutí 74Před rokem
cutting the frame off and prepping for new 2x3 tubing to go in on 1986 isuzu pickup extra 4 inch c notch for axle clearance
Making frame rails and using .0625(1/16") aluminum sheets for door panels
zhlédnutí 64Před rokem
Making frame rails and using .0625(1/16") aluminum sheets for door panels
What have I done? Lambo doors on a salvage titled monte carlo?
zhlédnutí 122Před rokem
2000 something monte carlo with "universal" lambo door kit. Kinda fun with roughly 10 hours of fabrication on the first set. I think it needs stronger struts then the ones it supplied and you have to fabricate your own mounts. less than $300 on Amazon
1986 isuzu pickup 15x10 with 195/55/15s and frame update
zhlédnutí 645Před rokem
we added some 15x10s with 195 55 15 tires and found out spring perches and frame are rusty. will be planning on doing some miata coilovers in the rear along with 2x3 square tubing to replace the oem frame under the bed
Isuzu mini truck project weber swap complete
zhlédnutí 71Před rokem
Finished up carb swap and moved through swapping out alternator and external regulator. Also installed a mig welder neck and handle from salvaged parts.
Weber carb swap pt. 2
zhlédnutí 247Před rokem
finishing up the weber swap and adding a holley fuel pressure regulator.
Removing 1.9L isuzu pup carb/weber swap pt.1
zhlédnutí 824Před rokem
Removing an old Hitachi carb that leaks, floods, and has a million vacuum controlled problems. weber swap install pt. 1
Quick tear down and rebuild/gasket kit for weber 32/36
zhlédnutí 3,9KPřed rokem
Shout out to @PuddinsFabShop for a little inspiration and direction on doing the weber swap on these minis. just toss that old stock carb and get ya a weber boys. this one was a great clean donor carb, it probably didn't even need a rebuild as it was in 9/10 condition.
1986 isuzu mini truck project
zhlédnutí 385Před rokem
1986 isuzu pup mini truck project. Step 1 get it running and driving Step 2 figure out which way the build goes...airbags with stock powertrain? static suspension with modified powertrain? jdm pure or all parts welcome?
DIY tensioner pulley 6.7 cummins
zhlédnutí 2,3KPřed rokem
Quick and easy tensioner pulley swap on 2014 cummins 6.7
6.7 cummins increase idling rpm
zhlédnutí 275Před rokem
basic tutorial on how to increase idle rpm to help your truck warm up faster in the winter
DIY 6.7 Cummins block heater cord install
zhlédnutí 380Před rokem
DIY 6.7 Cummins block heater cord install
Nice set up, If you don’t mind me asking, do you have a part number for the carburetor? I have a 82 S10 same motor. Thanks.
I bought used and rebuilt it myself (its very easy to do), this carb is a weber 32/26 (dgav)with electric choke. Brand new, they are just shy of 400 dollars typically, but I got this for 100 and spent 30 on a basic rebuild kit. When I bought it, the carb was very clean, but I used the opportunity to learn about it since I'd be tearing it down then reassembling
What adapter plate did you use for the install
I’m digging it. It’s taking me back to HS. The biggest dude in our school drove one like yours. Have you considered a full floor from a donor bed as the false floor?
looking real good
coming along fine looking good
How tight was your belt mine was a nightmare I had to use a gates belt gates tensioner and I used dayco for idler pulley. I checked the size of pulleys all the same, but the belt felt like an inch to short
Mine was very tight as well, but I managed to get it on. I used dayco for belt and tensioner
Hello, can you give me the Weber ref you put in? Thanks
Ref?
exact reference@@cromagmeditations1387
Nice
It's coming along a a little slower than I like. But I'm a busy guy
Looking good
Trying to give it at least 6-8 hours every week
Looks like it's coming along well
Yeah only if I could get more days off to do this. And I'm putting a turbo on a cummins next week so the frame job will have to wait
We're u get the kit at
Amazon special. I think it was about 230-250 and was "universal", meaning you have to cut up the car a little and weld plates here and there. This was my first one and I have about 8 or 9 hours tied up in one door
Wow
Ls all the way
It's definitely proven to be affordable, well supplied, and somewhat small in packaging for a modern V8
Can you link the cord you bought?
2013-2015 RAM 2500 3500 4500 5500 BLOCK HEATER CORD OEM MOPAR a.co/d/gnlGKac Hope this helps, I think it's selling for 55 dollars currently
Finally, fast tutorials for us youtube mechanics
That's the point of these. Quick little diy stuff to save time and learn something