Video

Is it finished yet

This helped replace my pump. I have the first gen LS in my 98 Trans Am and the water pump is the OG. The inlet will not fit any pump older than 2004. I learned this the hard way. GM Genuine Pump and it’s taken a third party inlet/thermostat to finish the job. Be weary and make sure it’s the original pump on these

So ive been trying to contact MG METAL WORKS with no luck.. How did you contact MG??

Yeah that looks unsafe being there in the back

What about the Tan wire with a black stripe at the transmission connector?

I LOVE YOUR VÍDEOS;my REGARDS FROM GUATEMALA CENTRAL AMÉRICA I'M MANUEL. I HAVE A ECONOLINE VAN 1988. WHERE CAN I BUY THE LIFT KITS. THANKS A LOT.

Anymore video on the install, so far this is the only video I’ve found on the MG kit, thanks for the tips?

How long is this bed? And will I be able to change to a step side once I do this?

How you take the lid apart to fix buttons lock

Damn idiot lock smith made a gap said I was filing a fake complaint and denied me service after fucking up my door, thanks bro 🙏🏽🙏🏽🙏🏽🙏🏽

What drive shaft did you get, I’m doing this project Very soon but don’t know what drive shaft to get.

Flyby? More like coasting by. 😂😂

I managed to fix a huge gap on my door caused by thieves

you do that kind of work

That big gear ⚙️ at 11:40 what is that entire assembly called? I recently have a rattle coming from what I believe is what your hand was touching at my mentioned time

I did the same swap but the truck stalls with put on drive

Let’s see some more videos on it ? Half ton suspension or 3/4

Hi what did you use as retainer for the high beam light bulb? My headlight assembly came without the retainer. I was able to only install the low beam light bulb. Please reply.

FYI to everyone doing the 4L60E to 4L80E swap instead of getting a custom drive shaft or cutting the original one and having to put trust in someone to balance it perfectly get a rear output yoke from a 1500 4wd and a Moog 447 U joint and your good to go without doing any extra customization…. But I’d still get a beefier shaft (same as OEM) depending on what you’re doing with your new setup

Can this work on an 07 nnbs long bed?

Bbbb bank I'm

socket heads not Allen bolts get it right

Hi where can I buy the kit brackets?

Thank you very much for this video. Much appreciated. Best of luck.

Do you know if those same mounts would fit a 1970 c10?

Very cool! how does it flex? would love to see it off road.

Great video …

Thanks Man. Great Help.

That look stupid, u gotta leave a little gap between the cab and bed

That’s why you don’t let other people drive your truck 😂 This was the best truck on this channel RIP 🪦

You have the most clearly explained video.

Bro, how you goin just skip to whalla it’s done.. People trying to see what tools, how to do it. Thanks for a waste

Thank you some locksmith just practically fucked me in the ass and robbed me and then left me with this gap as well 🤬😤

Where did you get the new hangers from ?

Wired the exact same way still not start and have pcm tuned 🤦🏾

Thanks I did mine wrong 😑 🤙🏾

What if you don’t have a piece of wood or something

Holy smokes that thing whines

did you disconnect the lower ball joint??? 🤔 thank you in advance

Nice video nice truck… … got my first Cummins 02 24v… what size tires are u running ?

Jeez, fix that exhaust dude!

Wow! There goes all your hard earned money out the tailpipe!

Were you located

Just want to thank you for the tip it really worked

I just bought a slammed Chevy like yours and my from wheels rub everywhere can you recommend me soon springs and shocks to raise it just a bit

What year 4L60E transmission vehicle are you swapping out to the 4L80E I'm asking because I am trying to figure out how to swap a 94 Chevy Silverado K1500 4L60E to the 99 Chevy K2500 4L80E transmission

So dose it require a transmission tune so It can gear ⚙️ right

My dad couldn’t do that and had to use a hatchet with a nail used for roofing. And bend around 3 inches below the top.

How about to make it regular short bed

Thank you bro! I can not believe I didn’t think to try something like that