Video

What’s the cost david

Uve never stated in %,sure only State,n percentage, give number ,your loosen people,wasted video!!!!!

It's not 4 to 1 ratio,try again do ur math ,folks ,tire size makes a difference

Dave, what kind of software or program are you using on your laptop, and what do you have linked to the motor to collect the data?

Thank you for your video I'm going to try and move my right rear out, i am a large racer and my kart pushes in, middle and out it's just miserable to drive and I'm trying everything with the front end and tire pressures but never did anything with the rear spacing, both rear tires are in as far as they can go so again thank you for your video and i will definitely start with the right rear

So if ur kart is pretty good but u want it to be a little looser center off could u add a little more camber?

You telling me its like spring rate just helped me alot, never thought of it like that

dude,you're a genius

So laying your right front down will help your kart turn if your pushing? Or does it mean i got to much left rear grip?or tires to soft all together? Or could it be im running to low air pressures? Where would you adjust first,but will laying the right front down help some is what im really asking?😳 Please chime in bro,🥺

you seconded the notion of my thinking,the guy.....😊

Low cross with high inside low outside on dry slick tire temps come off nearly exactly even after 39 laps. My temps ranged 182-183

If a local tract started a kart series but banned any tire treatment would you race it?

Huh???

If the ratio is the same on the mini gears vs standard gears what causes the difference in acceleration curve?

I like my hybrid

Great videos but the added in clips of comments kills it for me .

A inertia Dyno requires software, laptop, wiring, sensors in order to see the data *in the form of pounds*** A hydraulic Dyno requires oil and a gauge to see the data *in the form of pressure*** So when compared to dynos, why wouldn't a racer spend $100 on a tire pressure monitor system (tpms) that records the spike in pressure sending it Bluetooth to your phone app in a graph from just like the setup in this video? Takes only couple minutes to install and you can use on race day. You would be seeing your loads exactly as you see them in the video, only it will be in the form of pressure

In order for you to collect all that data, did you need the software, laptop, wiring and sensors?

Waaw super

Do you have a recommendation on seat height of floor pan per weight of driver? Like 90-110 pounds 1.5” off floor pan and 150-200 pound driver .75” off the floor pan? Just examples

It’s definitely difficult to be instructional at the track!

I really appreciate the videos. These came at a perfect time. Trying to learn this stuff to help my son, and there is just so little out there explaining the basics and the various adjustments out there we can be making for him on a race day.

I hope you do another video on the new mini gear systems, is their chassis dyno comparisons anywhere?

How do you essentially pick what RPM you want your motor to turn? I run a BSP sealed motor. The saying here is around 5800 rpm. We are on a big 1/4 mile asphalt with sweeping turns.

Thanks great help.

Is there a difference in gear ratio with a 120 link chain and 108 link chain?

I have been searching videos to understand cross weight and finally found it. Thank you for the video. Now i dont need to refer to anything when adjusting my rc car cross weight because i can visualise it in my head.

How much cross was added in this demonstration to show those numbers on your graph

I know its just a drawing but are your tires that offset from eachother?

z baar flexes more. its longer! bend a 24" stick vs a 6" stick what flexes more?

Phantom has 83 on some the charger has 95 and works great with heavier driver was the kind of information the people want. That was just an example. But your information was good to know. Now I know a chassis flexes.

If you wanna make a good decision, choose Phantom racing chassis...... period!!

Those of us with lung problems generally cannot be around an open container that has gasoline in it It's something about certain chemicals that makes our problems worse

I am 6,1 and 225 pounds and 35 years old . Racing a 70 + Horsepower Open Outlaw Kart with a cr500 . All my Kart does it push really really hardn...it's a S.K.E chassis ? Where should I start. ...The kart rides Wheelies on the Straits . Do I need some weight up front ?

This is very valuable information 💪

😀 Promo_SM

Probably one of my favorite videos on this channel yet. 🙌🏼 nobody talks about it bc it’s easier to just adjust one corner at a time. The high cross push is exactly what made me look into and understand more about chassis rake/ride heights

This is one of my favorite channels tons of information. And a great message at the end.

What you got cookin in the crockpot in the background?

Thank you bud the Lord has blessed me with the opportunity to go racing with my daughter it’s been 25 years since I’ve been around a kart your videos have helped me get up to speed and I love how you use it as a ministry keep it up

Man I needed to hear that for sure great video

great video and it shows what the setup should be but not how to get there ...

for me may be 50y of racing but you are so right what you just said thank you

So in that case would this be caused from too low of air pressure

We definitely need some more videos

With all this additional data is additional sensors required for it? Coming from a alfano this mychron stuff is new to me

Give us some more of those guitar solos David haha Really cool graphs man how can I setup a wheel load graph or is that a math Chanel you created?

I like the new music way better.

I know you want your seat mounting bolts with wiggle room, but what are your opinions on having that wiggle but also drilling the holes in the sest for the bolts a hair bigger in diameter to help with flex as well?

When you aay keep seat straight should it be straight with the frame forward or be straight with rhe steering column?