- 16
- 92 657
Tye Ouellette-Tolles
Registrace 7. 01. 2016
Random things I thought could be useful to other peeps.
Video
Demo Derby: Heat Three, Franklin County Fair Greenfield MA
zhlédnutí 345Před 4 lety
Franklin County Fair Greenfield MA
Dyson DC25 Wand Clip Reinsertion
zhlédnutí 13KPřed 6 lety
Response to viewer comment. This is how I did it.
THANK YOU So much!! It worked. I just pressed in those two areas you mention and the wand came out.
Thank you for the video. One squirt of WD40 on the wand handle clip (2:38) freed up the wand. Disassemble was not necessary.
This was exactly my problem and by pushing on both sides, it released the wand. My dyson does not work as a regular vacuum anymore (tried ordering beater bar part and it still doesn't work) but the wand works great. I have a new shark that does really well, but it 's wand is short and not very flexible. I use the shark for my area rugs and the dyson wand for getting in crevices. Problem solved. Thank you for your information, I have been googling all morning for a way to release the wand, not a kinked hose!
The handle wouldn't come out of the vacuum. I messed with it for about an hour, kept pulling up on it and finally, it came out. The problem with my vacuum, was once you remove the handle, there's a clear clip, inside the vacuum at the top, it was stuck.
4:37 for 10 seconds of information
Yeah, I can see that. When I make another, ill definitely try to keep it essential.
Talk about flog a dead horse, just say push these two clips tahr dah!!!
My hose was not the problem. I figured it out. When you take entire wand off, spray WD40 at the spring clips inside the wand, fixes it right away!
This is great info.
OMG!!!! HUGE THANK YOU!!! This helped me so much!!! I can’t believe that I finally found a helpful video! You just saved me so much money!
I am so glad to hear this!!!
+1 this solved it for me.At 1:41 you don't need to do anything with those. The two plastic things at 2:25 are just flat plastic, push from both sides at the same time and they'll go inside the housing and you can remove the hand and handle etc. You actually don't need the spring part inside since the wand and hose are non-functional except when the vacuum is upright, which is typically when you want use them and they can be pulled right out.
This is really helpful! Do you mind if I put this as text in the video?
@@tyeouellette-tolles4344 No of course not. The small orange cap tends to stick up now as there is nothing to hold the tube now the clip is gone. But it doesn't impact the performance.
Can you please post a video showing while talking i can’t figure this out
czcams.com/video/TopmWjvYnLo/video.html - the easy and proper way from Dyson themselves
C de
Thank you so much! It worked and you just saved me so much time!
WOw, I really wish your camera was mounted...
I definitely agree with you! I now use a selfie stick. Takes the queasy put of it. If you slow the speed that is easier.
great job! Spray spring with lubricant and run some along the gray tube. Night and day! if you are having trouble pushing it down for vacuuming, SPRAY SPRINGS NEAR ROLLER BRUSH. I Have a dc17
Thank you. Got mine working again. 👍
Mine is clogged completely how to unclog?
This video doesn't cover the clogging. I believe there are quite a few about removing them on other channels. Good luck!
I found out how! Water and clothes hanger!
@@coydog7902 neat. How didn't you get the electronics wet? Nice idea!
I did it near the sink
Thank you we tried it and it worked so well thank you so much
Nicely done. Nice voice too.
Would recommend that you talk about what you're doing and not to your child. Overall your video had no redeeming value whatsoever!
Take your screwdriver and poke it in? Eh? Where and how?
Hi there, you have a very good point-I use such technical Language. This part was hard for me and I found the best way to do it with using two screwdrivers and pushing In on the grooves at the same time allowed The attachment to come out. If you look at timestamp 1.40 This clip is the one I’m talking about. There is one on each side and like I said they have to be done at the same time. I got lazy at this part And I used a Phillips head rather than flat head. I scratch mine up a little bit I hope it goes better for you. If you need me to make a quick video Let me know.
*Excellent.>>>**t.co/jXKwwyY0ll** It saves me so much time and effort. I LOVE IT!*
Any one know how to reattach the wand cap? Mine came off one day while I was releasing the wand, and I can't get it back on.
Robert Maykut did the cap crack? Or the holes on the wand? In the video I removed it. The handle has a little flex. Put one side it the hole at an angle and slowly push the other side in. If this doesn’t work let me know and I’ll send a video...
Thank you so much for your video, I have managed to fix my stuck wand. You should get a job doing this you are amazing. I,m afraid the company were unable to tell me how to reinsert the plastic clip but with your help I have succeeded. Just like you I don't like to be beaten if there is a way to fix something. Thanks again for your help.
I can pull mine out but I can't get it back down to get it back onto the handle
That sounds like a jam on the lower tubing. This includes removing the hose. Keep checking...that’s all I could find when I started. Best of luck.
Yup
You have the extra attachment on. The piece is actually has to come out. The hose is in the right place just unhook the extra part (the grey part) that is used to clean the stairs.
The problem was that the wire spring got jammed and was preventing that piece from coming out all together. :(
Thank you, I am having the same problem. Do you have any pictures/advice as to how to fit the clip back in correctly?
Hi. I made a short reply. A previous comment mentioned removing the other piece. I agree with that but did not do that for the other video. czcams.com/video/aja95oWtD_k/video.html
Thank you!