Video

Just saved me $150.00 thank you!!

I watched your video on installing a 4-wire condenser motor. When replacing a 3-wire motor with a 4 wire motor I added the 2-prong capacitor and just disconnected the old fan connector from the dual run cap. Will the compressor run like this or do I need to jump any wires on the cap

Completely skipped the most important part, discharging the capacitor.

Is this motor 110 volts or 240 volts

Why do you need a three prong capacitor if only two of them are being used? Please respond quickly. I need to replace my capacitor and already have a 2 prong of the same microfarad

Hvac workers are scumbags and liars. Biggest con artist ever.

Thank you!

I have the dual switch as shown in the video. My question is when I checked the switch on the right it showed continuity with the inducer motor running. The one on the left showed no continuity. In the meantime my furnace motherboard is flashing that the limit switch is the issue. I checked it for continuity on the limit switch and it is good. Help!

Do you leave the other cap? What about the other wires on the other cap?

Does it make sense to say the single capacitor can last longer than dual capacitor?

A 9 year old video that was immensely helpful in wiring my fan. Thank you.

I replaced the original GE cap after 21 years of use due to age only....Bought the Genteq replacement and it only lasted 2 years....they are making garbage IMO....reinstalled the old one.

I have a red wire, a light blue wire, and a detached brown wire. 🤷🏻‍♀️🤷🏻‍♀️🤷🏻‍♀️

Do it matter what side contactor to attach the wires?

I need info on fasco d7908

Thanks!!!

Yeah he didn't

Finally! This was the video that actually solved my problem! Thank you! I even took pictures so i would know, but apparently the previous wiring wasn't right?

Hello why is my condensing fan motor stopping ,its a brand new protech motor I foolow your steps to wire it ( black,orange,purple ,yello and brown ) black to defrost board, orange to C in dual cap,purple to F to cap and brown and yellow put togeter it comes on but only stays on for about 2 minuts at the most ,please help

What size screw holds on the capacitor?

Life saver video thanks

Spoiler alert: Genteq is his recommended capacitor brand. The rest is just interesting info about reliability, testing, market forces and similar subject matter.

Black/blue - C Yellow - Hermetic Brown - FAN Your welcome

I have a dual capacitor in a ceiling fan a cbb61 and it’s 1.2uf and 1.6uf but cannot find a replacement. Any ideas?

Am Rad maybe

Maybe you want to add a caption to clarify microfarads are one 1,000,000 of a farad 6 zeros micro. I think.

What about the the lead from the compressor

Just need a wrech and a socket

Are both pressure switches the same?

What if my original wire the black wire came off the board, does it still go onto the Contactor?

Have a capacitor with 50 v 470 uf yxg on the end what does yxg mean thanks

Excellent video. Very well explained.

No measurable voltage on the white wire...

WTF 2 minute commercial???? correction 4 minutes.... bye

I tested a -.10"wc on a goodman system yesterday tested the collector box cover was reading -.17"WC but the voltage was fluttering on the switch even thoe it was over manufacturing rating so i have ordered a switch see if thats whats up

When he said there is no way to tell the pressure inside the pressure switch unless you have this special tool (600 bucks) ... Well they need to update those things to look more 21 st century than mid 20 th. They could have built in digital gauges or a universal port to give you a better understanding of just what your furnace is doing ?

One other issue can leave the pressure switch stuck in the open position - debris in the air tube nipple that the tube attaches to on the inducer motor. Our Goodman furnace was blinking an open pressure switch code on the controller board. After determining the correct voltage was reaching the switch and that the air tube was not leaking, we then tested that the switch could close by sucking on the end of the tube and checking for continuity through the switch. As a final test we turned on the furnace power and sucked on the air tube - the diagnostic light on the controller board stayed lit, indicating no other issues we could detect without testing the switch with a manometer. Rather than opting to climb up on the roof to check the chimney next, we took a stiff, thin wire and reamed out the air tube nipple on the induction motor - it felt a little crunchy! We reconnected the air tube, and lo and behold, the light on the board stayed on and the furnace ignited! So, before inspecting the flue for a blockage, clean out the air tube connection on the induction motor.

Brian Khoberger?

Thank you very much for posting this and other videos. You explain the subjects very clearly. Is it possible to replace two single capacitors (a start and a run) with one dual capacitor? I ask this question because I was unable to find a single start cap with 30-33 uF.

Is working near the capacitor particularly dangerous? Is there anything we should do to make sure it's discharged first?

Thank you for this. Not only did i get the part from you guys, but had an easy time installing....and saved $1000 by not using my hvac guys (and refuse to use them ever again, what a rip). Crossing fingers this does the trick !

great video. thanks!

I believe it is called T1 T2

Video has no volume. You need to use a better recording system

amazing - how in a short time someone is able to give technical knowledge - even understable - THanK You so much... I got it within a msec from your video what I wanted to know (if I can't put a 5F ---> 1.5F, the answer is NO) Thanks again and please go ahead...

z best capacitor in z world is Italian capacitor undeniable

What about herm.

All of the local HVAC parts stores in my city stopped selling to the general public. I used to be able to walk into the Trane shop and pick up a usa capacitor for under $30. I think the local HVAC union pressured them into it.

What about herm

Perfect video😊