Video

Plz expline drum level transmitter

Hi.the great video.how to verify calibration with pump if it is minus - mmH2O

Pressure on Low pressure port should equal to the process gas pressure in the tank - Gas pressure will exert in all directions at the same value.

👍

Formula for calculation sir?

actual dp in this case ( dry leg) is not zero without opening the equalizer valve !!! sg1*h2 can't be equal to sg2*h3, isn't it? other thing i think that BV2 should be open too so that the LP measure cell will be communicating with the empty part of the tank that may be little bit pressurized above the atmosphiric pressure.

H length mm or meter

100 % diesel means how will get process gas SG again. 100 % means Lp side taping point also filled with diesel. Otherwise Lp side tapping point should be above the 100% .

Ye video kya england walo k liye hai law*** English me bak diya. ,sale khate bharat ki hai ,jhadte angrezo ki hai mc

The video is good in terms of knowledge that it is trying to transfer to the audience. However the video seems very strange. I don't what's the relation between technical analysis graphs in stock market with DP level transmitter. Your video is a tool for communicating your message not for making unrelated visual noises. I tried to fokus on the content and expected your video as a part of your content and then became confused with the visual features there. Don't do that in your next videoes.

Good job

Sir . Could WE do this technique of Et leg in process that thé température IS minus 33 and pressure of 60 bar

Hello boss, can I please receive instructions on how to measure the quantity of liquid in a closed tank using the Differential Pressure Transmitter, if possible

Hello there, sir can i ask how did you know the specific gravity of diesel at Hp and Specific gravity at Lp 0.008 how did you know that i know the formula for Density = density of subtance /density of refernce how did you get that please sir answer me to calm my mind thank you

We put always the HP at the top of a closed thank. So the range is always negative. In case of leakage we always measure 100% (overfill)

Such an extraordinary presentation

Its really more useful. The way it is explained is easy to understand and follow. The very basic concepts with clear explanation. This will surely help the new beginners.

What is to be considered(SG) in calculating LRV and URV if your process fluid is water? SG(air)=0.0013 or SG(water vapour)=0.6218 Or SG(water)= 1

Sir pressure tx se tank ka level check kr sakte h

Please explain.. when diesel is at its 100% level.. there is still process gas present in the closed tank..and this process gas is continuously exerting pressure on the HP and LP leg. Why did you not consider the process gas static pressure when URV is calculated?

Nice 👍... Keep it up 👍

Very nice Dear 👌, Great Job

When 100% full tank then diesel goes to dry leg and full of diesel in dry leg LP side🤔 please explain what happen in 100% full tank of dry leg🤔 confused

What a superb strategy 👍, sir please make video when we use 250 ohm resistor in calibration in field as well as lab,, doubt🤔

👍

Nice, but you dont have to open equalizer to make the water flow to the DPT, after the opening the block valve the water directly flows to DPT, the equalizer valve position om the middle of the passage through the block valve 1and 2, but not blocking the passage through the DPT diaphragm. BV1 BV2 | | |__________EQ__________| | | | | DPT and also if you are zeroing a DPT you have to eliminate every pressure to the DPT, or open the equalizer to balance the pressure exerted on the diaphragm.

Clearly explained

👌

Nice 👌

Super

Good one

Well explained sir!

Good job sir

Well done 👍

Thanks for sharing such good content. It will help a lot for others.

it's really helpful sir thank you, Have a good day sir

this video is very informative. thank you so much for your good video.

Nice 👍

Superb annaaa👏🏻

more videos brother 😊

Well explanation👍

Nice 👍

Super... Clear explanation...

Super ji valthukal

Nice 👍

Good one.