Video

AMS Regulator comes in many variants to begin with Fixed and Variable (1.5v,1.8v,2.5v,etc)

In my case its red LED glows when battery under charge when full red when off and green constantly ON when no battery or under charge or full from where did you purchase this ?

can u pls tell me how to do it in tinkercad, i need it urgently for my project plss

Fake video😢

Its is working? If i symbol this video????????

This is a great example of how something inside the bubble is completely weird seen from outside the bubble. No idea why manufacturers of silicon simply don't put like GND, +5V, -12V and such at the pinout schemes instead of this random garbage. Same as coders who do tutorials with Foo and Bar as variable names. You may hit them with a baseball bat as well.

What about circuit diagram

Circuit diagram

Good Job I will save your info for future need thanks

This is the fakest thing i have ever seen

But it's hot

🧐💩

Did you install the B772 transistor upside down or it didn't work for me?

👌👍

this works but it destroyed 2 s8550 transistors and had lots of glitches and i burnt my finger after touching the s8550 transitor because it gets way to hot edit: it was prob because i used 8ohm 10w speakers which drew too much current and blown out the transistors. now im testing it with 4ohm 3w speakers and so far so good edit 2: it works great and very loud and i used it to make a subwoofer, but there is some noise with some chargers

Can someone please explain the flow of current in this circuit?

I used s8050 and it worked

Brother i have a question,i have build the circuit like u did,but the thermistor dosent work,the led with or without the sensor work,can u reply pls

Does it also work with the cd8227gp?

how the laptop for example is working even after disconnecting the charger ? there is a capacitor or something that keep the laptop up till the switch is connecting to the battery ?

I did this project and use the 9 V battery. They did light up for a few minutes until they all burnt out.

Please give the code :)

Transistor 2N2222

this is the best tri-state buffer explanation, combining gates and transistors. Easy to understand.

Hola amigo lo hice pero no me funcionó como me saca un ruido en la salida y no se escucha nada de amplificación. que puede ser?

HELPING OTHERS TO GET KNOWLEDGE IN ELECTRONICS IS OUTSTANDING. GOOD WORK. PLEASE CORRECT THE CAPACITOR VALUE YOU CONNECTED THAT IS 100µF AND WROTE 470µF IN THE VIDEO.

Have the circuit diagram? Plz.

Can I get a diagram to make this :))

Fantastic capacitor feedback information. Great for circuit board designing. 😎 Thank you.

So much beautiful and like 🙏🙏🙏🙏👍👍👍👍

AN5270 ? Yes/No?

Could you have 2 die so they could be used for cribbage?

I THINK THAT OPEN IS NO POWER...

NICEEEE

Thanks, I want to try

Excellent video !

Very nice video 👍👍

He ic maltimitar se kese cheak kare

apakah bisa menggunakan elco 25 v 2200uf pada bagian out speaker?

Gracias , súper bien 👍

Where are the necessary calculations?

This was quite useful. I'm trying to get some micro linear actuators working, and the full & half step methods seem to work if I get the stepping frequency right. I'm going to try using an A4988 just to check the actuators are ok.

ali lo que esta funcionando es un solo canal..

A very good lecture. But I have a question. Are these corrections found for MPU-6050 are written into MPU-6050 memory permanently ? In this way, do we have like a new MPU-6050 ?

Is it a 0.25W resistor?

I just rewatched your video and found you used 12 V for the circuit, but are you using +12V and -12V (bipolar supply), or just using single voltage supply (12V and 0)?

How much volts are you using to run this IC, plz?

𝗪𝗢𝗪👍👍👍

great video! thanks bro

Anyone know if these require low voltage? 120? 240? Looked like some euro type plug he used