Video

Been pronouncing Bode wrong 😭

Is Vin from the function generator?

Can you explain Vin and Vpp? Is Vin and Vpp coming from somewhere?

Love the corporate lies. The input hardware can handle the bandwidth. You fools purposefully software limit the input bandwidth to make an excuse to charge insane money for a scope. Siglent and rigol are going to put you guys out of business.

When I perform a full 2-port calibration using the Ecal kit N7554A with my FieldFox N9916B, I observe an insertion loss of -4 dB for S21. However, when I perform the same calibration using my mechanical kit, no insertion loss appears for S21. Can you please assist me with this issue as soon as possible?

Amazing keep up the good work

HI, I´ve installed the Command Expert 2023 in my PC but new tab wasn´t added to excel . Is there some special procedure to be done during/after installation to get the new command expert tab onto excel ?

Do you use straight through cable or null modem cable? Thanks

Good afternoon sir please explain the waveform generator connect to pc via LAN cable steps sir no direct steps sir full detail steps explain sir

very simple,quick and clear. thank you!!

This XY mode is supposed to give a linear signiture measuring a component or circuit path through a curve tracer octopus which gives voltage through channel one and current through chanel two. The two signals will have zero phase shift. The supply power to the octopus can be 115VAC stepped down to a much lower voltage through a transformer or the AC source can come from a waveform generator where you can control the frequency.

Good morning sir please tell me about waveform generator connect to pc steps sir please help me sir

While teaching undergraduate courses at UCCS (University of Colorado at Colorado Springs), I mentioned briefly in an early lecture that if they were to connect an oscilloscope to the the AC outlet (in the US that is ~120V @ 60 Hz), that they could "see" the sine wave. Of course, some student tried doing that using a passive probe when I was not in the lab. BOOM! Thankfully nobody was hurt. The probe was toast. I was very careful what I said in future lectures!

hi sir, how to calculate the inductance value of resistor at high frequency. we have Keysight lab in our university we r having spectrum analyzer ,vna , oscilloscopes but idk how to calculate it. our oscilloscopes r having maximum of only 100 mhz so we cannot generate using it.

can anyone help about changing the battery for this probe the battery screw don't want to be disassembled

❤❤you are such a gifted lecturer I would like to express my gratitude

greate tutorial, thanks

sir instrument connet with pc via lan canle steps sir his video i con't understand sir

waveform generator connected to pc in steps please help me sir

absolutely fantastic content, thank you so much for putting this together!

I feel blessed to have found this old man. He's such a good teacher, something that makes this CZcams account to be such a good channel worth of my attention and subscription.

Good tutorial, nice clear explanation and no irritating waffle! Thank you!

Great Video.

I can't understand what is being said. The accent is very thick. Maybe giving the script to someone that can clearly read it.

Hi , we can not see that graphical plot in the meter menu , how can we sovle that ?

Hi, we have E4360A and after getting connected to the instrument we can change operational modes from the brower; BUT we can not see the graphical I-V curve plot shown in the video; what might be the reason for that ?

Nice demo! Thanks for your video

Johnnie retired. Then he came back! The man has passion!

I'm loving this series but I guess, I started learning on an analog scope so it makes me nervous to think about jumping to a digital scope. Partially because a lot of the new digital scopes are so expensive if you want to get professional grade

Any particular model designed to decode bacnet mstp?

very informative

dear keysight, i have a B2901B SMU. Is it compatible with the keysight benchvue software? When I set the software in demo mode, I cannot find the B2901B model... thanks

Good job though I bought a Rigol DHO924s which has almost everything hackable inside.

Right on point, thanks.

Sir hope you are fine I have question to ask from you. As I am following you on youtube. I am using keysight 2000 series DSOX2014A. It has specs like memory depth is 1MPTS and sampling rate is 2 Gsam/sec . As record length = measure time x sampling rate When I measure the measuring time to utilise the full sampling rate I.e 2 Gsam/sec . I have measure time = record length /sampling rate So MT = 0.5 msec total time length 0.5msec/10 = 0.05 ms / div But when I increase time per division upto 2U/ sec I have sampling rate 2 Gsam/sec . But when I go up to 2.1 usec it drop to 1 Gsamp/sec . Why ? It should maintain the sampling rate upto 50 Usec . Please help ...

Very helpful, thank you!

In current version there is no more manual configuration tab....

Can you add affects to it like distortion ? from a pedal or pro tools ? Can you add a chain ?

Every time you said trigger someone's dog named Trigger started tearing up the couch. I hope you're proud of yourself.

nice sharing

My giant HP power supply has some really fat caps inside. I think they are in a similar range if all of the values are combined. That power supply looks so interesting. It has a lot of stuff inside I have never seen before. As it is sold for about 1000€ used (about 9000€ new back when it was released) I think that is to be expected. Luckily I got that thing for free because it wouldn't output any power. I found a tiny blown fuse the size of a resistor and after replacing it, everything worked as it should. I'm happy I was able to save that thing from the trash. It can output 0-60v and 0-50A (combined max. 1000w). It's really useful for a lot of stuff.

Thank you I would like to measure R.I.F.E. Frequency that I hear. I would like to be able to put in print what I find, also have an opportunity to jam the signal, can you help me understand how to do this ?

Very illustrative!!! John, we enjoy all your videos!!!

i wish my dad was a multibillionaire heheheheh i wouild buy the full set

this is a great solution for remote internet and logging data . do you have any solutions for the actual remote daq that you can mount in box and leave on some device to measure?

Can i block the value on the screen when i see it?

Can I block the value on the screen when i see it?

Can I block the value on the screen When i see it?

Can I fix the value on the screen when i see it?

Stupid Errr_connection_refused