Video

Good deal. Thanks

Amazing job, I have the same boat. Too bad the triple backflips were off cam.

Thank you. Who designs those things... surely ergonomics and comfort should be big on the list.

Im hoping this works for me because im in the same boat. Thank you for posting the extremely helpful video ☺️👍

This looks like the situation I have now, But my hole is directly underneath the O2 sensor, and the flex pipe is starting to go.😢

Thanks that was super helpful and I really appreciate the visual demo.

Ypu cant use pressrue treated plwood in an aluminum boat or you will destroy it. This is not a good idea, you are better off using regular pywood than this. But really they make marine geade plywood juat for this purpose,and other than replacing your wood floors with more aluminum, marine pkywood is the only good solution to rotten floors.

I think they adjust these newer headrests for the new gen of kids with forward head posture because of always being on their phones

Thank you, nice 👍

reset the springs. It takes 30 seconds and anyone can do it.

I still think removing the trans line and allowing it to pump out is worthwhile... It was able to pump out a little less than 4 quarts...

My 2020 f250 drives Me f... nuts! The headrest are definitely getting adjusted

Good idea on brake light check

Excellent video!!!As a side note, Bug was heard saying: Hey, Mister, can you please go somewhere else to do your teaching videos??? I'm living up to my pest expectation... Don't make it harder to get inside!!🐞🐞🐞🪲🐛

What the heck is all that clicking noise!!!!???! 😡😡😡

Why didnt you run power to the solenoid to see if it moves in and out?

Just came across your channel 👍 What lower end scanner do you like that can analyze the powerbalance, VCA bank 1&2, etc for troubleshooting?

Next stop Gold Slucing!

American Standard Canadian Cadet Toilet

wow, pretty sure thats the same engine as my Ford 1320!

i believe pressure treat wood will eat up a boat, so just use plain ply wood an put resin on top to make it water proof.

Super

Car

what are your thoughts on just putting the 3/4 plywood all the way to the back? I have another soft spot over the gas tank. it's not terrible, i'm 300 pounds and i can walk on it but it definitely flexes and the carpet and gel coat on top are rubbed away exposing the old wood.

cheapass crap made under brand names in China

Thanks for showing the cable routing, and pointing to everything. Put Rhino 700 in the video title if you can, it should get you more views!

I took my glass apart and when I did the springs fell out . Any clue how to get them back attached to hinge . Or would you have to replace . Nothing looks broke just spings fell off so door isn't closing at all. 😒

I just love how you literally skip the hardest part to do in the whole job! I'd bet 900 of the thousand views you've got are to watch how you installed the snap ring and you skip it and show it done and explain how you did it that's not how you make videos of how to do something!!!!

Nice!

This is the best alignment video i can find, you're the man.

I had a broken wheel on the bottom of a slider wheel. The wheel is spring loaded with coiled spring. I could not find this type on the tube. However, this video helped in adjusting the top and bottom tension screws well enough to operate the slider smoothly. Thank you very much for this video.

I thought I was the only one that was complaining about this horrible headrest design 😅

I like it! For the older boats that aren’t worth dumping tons of money into this is the way to go.

For the amount of work, just get a new sway bar with new links and bushings unless you really don't value your time. Boss 302 set for the rear with already mounted links and new bushings is $150-175 and comes complete.

Nice watching you work thru that. Any update? I would have thought that 12” of runway would let the egg build up too much momentum to not break the eggs

Nice job.

You did well removing the bend, however the inside bead where the rubber tire bead meets the aluminum wheel needs inspection and possibly a rasp file or emery cloth rubbed completely around the repaired area otherwise mounting a tire on an uneven and rough surface e will surely create a slow leak that will empty the air in your tire in a couple days!

I need to make a U shape but more like no rounded ends all 90* degree so it can go from the front of the house gutter immediately around the house (1” away) but it’s a 90* degree corner & all the bendy ones don’t turn sharp enough since I buried the corrugated pipe up against the house how can I do this they don’t sell this piece I’ve been looking for months

Excellent video. Thank you.

Just dumb, without a solid measurement, a Story stick as a guide to show how far. So sick of eyeballers/ 150 celcius is a joke also not even enough to bother paper. Just no experience might as well be cold Propane to 700 F. Pressure of a jack is less harmful/ Fracture as you may

To close the gap, cut a short piece of pipe and snap it over the gap.

😂 omg, too funny! Use an air or hydraulic jack and slow pressure to avoid this comedy sketch.

Well done sir .

I wish I could figure out how to keep it from coming off of the track when my 10 lb cat lunges at birds on the balcony. He almost went right over the balcony last week. 😢 It's our first time living in an upstairs apartment. He's never bothered screen doors before. Birds and squirrels were always around. I'm not to leave the slider fully open, but it's hot. Is there anything that I can do to make it a little harder to come off of the tracks from a simple impact? Thanks for your video!

This video wasted my time

This will not last long. I made separated sway bar links and even used the old bushing by reducing its circumference

It was probably the test leads when you moved it happens to me all the time, especially the sewing pin, even the clips, can give Intermittent faults. Metal oxides are semi conductors. Stainless steel is a weirdly good and bad conductor

I wonder if you could have put a small piece of adhesive foam on the top too to dampen the closing noise. You’d need the counterweight though. I have this problem in my master bathroom. Gets annoying when it’s windy.

So you drilled right into the top of the stringers? Did you put anything into the drill holes?

Great video DIY guy !