- 27
- 76 577
BigStyle Garage
Registrace 4. 04. 2013
Video
Ebisu Fall Matsuri '23 (Handycam)
zhlédnutí 619Před 9 měsíci
Took my trusty old early 2000s Handycam to Ebisu Matsuri, the first one i have attended. Absolutely blown away by the madness of this event. Here's what i managed to capture :)
pretending its '02 (e46 m3 touge run and a beer)
zhlédnutí 762Před 10 měsíci
Copped a handycam and gopro, took my dads beema for a drive in the hills coz nissans always broken :(.
350hp for 5k? RB20ET Cost Breakdown
zhlédnutí 2,4KPřed 10 měsíci
decided to do a bit of a tally up of what was involved in turboing my RB20e.
rambling/backstory/life update
zhlédnutí 515Před 10 měsíci
bit of context behind the 20ET build and where we are headed. Instagram @bigstyle_laflare. Intro music - DJ YUNG VAMP
WORLDS MOST POWERFUL RB20E? We hit the dyno again!
zhlédnutí 4,2KPřed 11 měsíci
Took the laurel back for a retune after installing the kelford cam, great results but still more in it.
RB20ET Laurel gets aftermarket camshaft. Sounds rowdy!
zhlédnutí 4,9KPřed rokem
We finally completed the install of the kelford 274/274 rb30 camshaft into the rb20e. Hopefully this should allow us to rev it more and make more power.
C33 Handbrake conversion with auto console
zhlédnutí 409Před rokem
Quick video explaining how i have rigged up a handbrake using the auto console
RB20ET C33 carpark drifting
zhlédnutí 3,8KPřed rokem
Took the laurel out for its first shakedown. Hawkes bay tarmac motorkhana. No issues at all, Stoked!
RB20ET hits the dyno, sounds insane!
zhlédnutí 3,1KPřed rokem
Took the rb20eT to the dyno and had her tuned. Ran into knock issues surprisingly early but we will be back for more power.
RB20ET Laurel ready for tune! +Rev limiter testing
zhlédnutí 4,1KPřed rokem
We got all the upgrades from the last video installed including wiring up the new computer, and i have a bit of a play around with setting up a rev limiter on Tunerstudio.
Rb20eT go fast bits
zhlédnutí 1KPřed rokem
Bit of a yarn showing all the supporting mods for the big turbo 20e Follow on Instagram @bigstyle_laflare
Big Turbo RB20e+T first start! Sounds epic +Aeromaster bodykit fit-up
zhlédnutí 9KPřed rokem
@bigstyle_laflare on instagram
Big Turbo RB20e+T: fabricating a turbo manifold
zhlédnutí 3,5KPřed rokem
Big Turbo RB20e T: fabricating a turbo manifold
K24 C33 Build Update + rb30det 5th gear burnout
zhlédnutí 2,3KPřed rokem
K24 C33 Build Update rb30det 5th gear burnout
K24 C33 Build: Painting subframe and underbody +updates
zhlédnutí 497Před rokem
K24 C33 Build: Painting subframe and underbody updates
K24 C33 Build: modifying the r200 subframe (diff raise)
zhlédnutí 305Před 2 lety
K24 C33 Build: modifying the r200 subframe (diff raise)
K24 C33 build: Long block freshen up, designing a new sump on CAD
zhlédnutí 368Před 2 lety
K24 C33 build: Long block freshen up, designing a new sump on CAD
K24 C33 build: Fabricating a custom sump and oil pickup
zhlédnutí 2,4KPřed 2 lety
K24 C33 build: Fabricating a custom sump and oil pickup
K24 C33 build: Making engine mounts and a remote shifter
zhlédnutí 980Před 2 lety
K24 C33 build: Making engine mounts and a remote shifter
C33 Laurel RB25DET NEO swap walkaround
zhlédnutí 19KPřed 3 lety
C33 Laurel RB25DET NEO swap walkaround
Thanks for sharing this info mate. Any more updates on the project?
go look at sammits bogan 32
Would you send me some specs on the parts you used???? Please
@@BrandonJay1983 dm me on instagram @bigstyle_laflare, ny previous video “go fast bits” shows most of what i have used though
God dammmm🤤single jingle living life
Absolutely love. 2b20e's are where its at!
Hey man u still got this
unfortunately had to sell it as I moved to Australia. Have started a Jzx110 build though so will have some content on that soon.
Nice is the laurel still loving life do U know? Have a few 20es sitting around I need to make the most of 😅
@@iloverice6600 As far as i know shes still in 1 piece!
Solid
what cam is in it?
If I just want to toss a cam just for the chop in my rb20e single can do I still need a tune or can I get away with factory ecu
Your car might run, but probably not very well and it might damage it over time. I cant confirm as my car had a standalone ecu by the time the cam went in
verry nice bro! hello from Russia =)
Sadly the cam module / distributor CAS are pretty bad for timing scatter on the 20e and 30e. A rb20de head with proper CAS will solve that issue plus it won't have the hotspotting issue that the single cam heads may or may not have.
Can you elaborate on two things? 1) cas trigger disc conversion and setup. (How’s the harness bit sorted? TDC signal to Ecu allows Ecu ignition output channels to be used to fire CoP units, which are powered/grounded accordingly?) 2) RB20E(T) oil pumps. Did you change yours? I’ve got the factory 20ET and I’m pulling the engine to do paint/body. Hoping to proactively change the 100k replaceables as well as oil/water pump. Not sure if the 30e/et pumps are direct replacement for 20e/et. You should broker some 20E/ET parts thru your channel, I’d def be a customer lol.
1. yeah so basically since its still en efi engine the dizzy has a cam angle sensor in it and i used the signal from that to trigger the coilpacks. look up rb30e CAS wiring diagram. the loom is custom with a stand alone ecu. you dont have to change the disc inside he cas however i decided to for a more reliable cas signal as the nissan 360 discs have been known to cause problems at higher revs. 2.I have not changed my oil pump but i imagine the rb20e/et/de/det pumps are all the same as the block is more or less the same. Good idea man il look into that.
@@JackBatchelor33 thanks for this minute you took! Legend! 1) I’ve got a Megasquirt ms3 so I’m thinking similar reliability with the trigger disc swap. 2) sounds reasonable, I’ll pull mine first before ordering a replacement. Hope you find room on the channel to tinker with the single jingle some more man, cheers!
What fuel are you running ?
Bp 98 octane
Is this a turbo cam or just the NA cam?
Turbo cam. Type “F”
How you ran your exhaust? what material? What header? Sound nice.
Its a 3” stainless all the way from the turbo to the tip, no mufflers. Manifold is a thick wall stainless one i made myself
Any videos of setting the timing on this engine
I try to explain the process in this video, what would you like your know? Dm me on instagram @bigstyle_laflare. Happy to try and help
what a peace off s t
🤙🏻
Do you have instagram also?? Love your work
@bigstyle_laflare
What gearbox do you use?
Rb30e. Rb small box, same as rb20det
What intake manifold?
Standard
What intake manifold?
Greatly enjoyed the foods Cars also go good Especially that rb26 swapped chaser 😍
In the Graceland, have fun bro✌🏻
Looks sick bro, hella jealous!
❤ good fun.
Hope you have a mean year in Japan 🇯🇵 brother all the best ❤
Too Chur bro !! Love the plate
Good content ❤
Gangsta footage bro!
i see yashio factory i click
I see Sammits car I click after what social media has been like. Can't wait to see his newest vid
What a mf burnout aye 🤣
Been looking for a video like this. There’s barely any info for the rb20 e
nissan reliability sometimes.
Gaw damn bro, thats mean!
Thanks for the breakdown. Even if I tried, I would only get about half of the visuals done.
Nice bro!👍good luck with your travels.
🍻
Vh45de with ITBs would be mean 😅 yakuzacruza
do you think id get any problems without doing the coilpack coversion ,i have a greddy blue ecu
Yeah i think you will be fine but may end up with a weak spark. I have heard of the dizzy setup failing when it gets warm. Im not super clued up about how ignition timing tuning works with a dizzy either
Good car control man. Top skills. Thats a really tight course to get a slideways 33 around! Be interesting to see the difference between your times and the little honda powered FWD rocket there. Grip versus Drift.
looking to turbo my rb20e, what size injectors are you using? could you drop a whole parts lists or do a detailed walk through video at some point? thanks!
Check my channel for previous videos showing the build process, iv tried to document everything. Injectors are 875cc
Thank you!@@JackBatchelor33
Hawkesbay no shit 🙌🏽
You're ripping it 🎉‼️
I'm doing the RB20ET on a miata, any recommendations or something I hve to address in order to make it right 😅❓ Im hoping to get 200 to 250 hp is it possible on the stock turbo with a tuned Reprogramable ECU ❓
I dont know a whole lot about the factory 20ets as mine is a 20e+t. Probably be at the top end of a factory turbo with 250hp but as long as you have good fuel and injectors it should make those numbers.
The 20EGOD plate sheeeessshhh🔥🫡🤣
Aye i know i had to find a trini best driver taxi laurel men dem lurking🤣
@@meatsauce8454 it's good research
@@MariTheMenace very tru sammit did it also could look at that also
@@meatsauce8454 thanks bro I checked it out
Congrats bro. Cant wait to see what you do with it🔥
Big fan
Haha sounds epic 😂Just listening to it put a smile on my face!
Worlds most powerful and worlds best sounding 20e 🎶 Great build!
Sounds tuff asf. Great setup
Hey man i've been following and watching your videos for a while. I've been in the market to get a gte skyline which shares this same engine! I would love to be able to talk more about your experience with it some time! Do you happen to have a tik tok?
Hey man i do but dm me on instagram @bigstyle_laflare
@bigstylegarage on tiktok