Video

Hi! So for some reason after I did this swap out for my LEDs, they wouldn’t last more then 10 minutes on with a 10a fuse. I had to upgrade to a 20a fuse because it would not last with a 15a fuse either but now the driver side visor light won’t turn off. It was working fine at first but then this morning, the light would not turn off and the visor is all the way shut. What do you think might be causing the issue?

This is FANTASTIC, thank you sir!!

Just says sorry i don't know about that

That's why I buy soundbars, don't have to deal with any gain bullshit lol

Hi! I have the 2025 e-power. Does this led bulb works the same for this vehicle? Thanks!!

why are you calling the battery cell a capacitor???

Have you compared your real world accuracy with the timegrapher data? I’d be curious how much variance there is between the two

How about the light in the center storage between both front seats?

Hello, thanks for this video; when you start the process with left speaker against the wall, is the right speaker turned on also?

​@COGuyStuff --- Do a review of the Gamepod 1.5 and Interactor Cushion!

Thanks buddy. Just used your link to order mine.

Full size buttkickers ! Yes yes yes 😅 not overkill.

I have this same I want to upgrade 4gb soldered slot + 8 GB replaceable. Am I to simply replace the 8 GB with 16gb or solder the 16gb to the Soldered slot

Thanks for the videos. Word of caution: Dirac’s resultant curve is a loose prediction based on what it “knows” about your room-which isn’t a lot. Measuring actual room response post calibration with REW often differs quite a lot from what Dirac predicts. Unfortunately, Dirac’s resultant curve isn’t a reliable guide for what your crossover changes are doing to your room response. The best thing I have found to do is trial/error the crossover in Dirac then measure with REW. I get much deeper, much more even bass doing that than following Dirac’s prediction.

Tip: Cut the braided sleeve at an ANGLE!

Wow, that is excellent! - I'd struggled to get SmartThings to relink with Harmony until I found this - now it works like a dream, and so fast! Many thanks for making all so simple to follow 👏

With a power conditioner it is not just about sound.I have a Panamax 5400 PM and when power is connected or there is an outage the outlets engage one at a time instead of all power on with a power strip.

I made it after 90 minutes struguling 😅 they worked after putting the led to all and test each one. but all of a sudden all of them stop working 🥲 any recommendation?

Ahh thanks for this. Don’t know if this one I got from China will make a diff on the battery change but the guide to swap was helpful. Thanks!

Didn’t help me at all, sadly. I can stand a foot away from the one I want to respond and the one that answers is literally the furthest away

How did you time align the Crowsons with your other speakers and subs?

Is updating the firmware in the c2 a must? Mines out of the box too

Thanks a lot for your video. Before purchasing the RAM I verified that the original module is @1866Mhz (PC3-14900), while the one you choose is @1600Mhz (PC3-12800).Can you confirm that this does not affect the performance/compatibility? I found another kit @1866, still from crucial: CT2K8G3S186DM, it says Mac compatible, but the timing, speed and type are the same except for the speed. What do you think about.

Thank youu!!

Thanks mate, used this method to do cables for my 5.1 theatre setup. Pretty much same gauge amazon cable, same sheath/loom, plugs and shrink tube. The only different thing I did was to use a small amount of clear sticky tape wound around the sheath and cable to stop the ends from fraying as I slid the Y pants on. Was having a bugger of a time before that.

thanks Chief

I also gave this a try yesterday and i can hear a clear difference but cant say i like it better. I watched Edge of Tomorrow with it today and it sounds just like i’m cupping my ears. Its a very similar effect. I can make the effect go in and out by rocking forward 10-12 inches. It’s pretty wild. Im going to run it again but be 2-3” back. So more of a 5” from headrest then apply the 8” rule. But yeah its very similar to cupping my ears as if you do when youre trying to better hear whats in front of you. Thats the best way i can explain it. Thanks for the inspiration to try new ways to calibrate

Curious as to why you didn't mount the new horns where the old one was. Great video though! Thanks!

man i need a amp for my dual pa 18 inch subwoofer no cap

I can’t thank you enough! I have two five gallon containers that I fight with. I can’t wait to swap the spouts out.

Is it real leather?

Bought the same ones on Amazon a few weeks ago. So much better than the crap that it comes with.

Actually that is what the world used for decades before the spout we grew up with. They actually work quite well but are a different operation.

Good Stuff, just no "toasting" Sticks when working around Gas Fumes....

Most useful vid yet.

Thanks for the vid. I’ve just been living with this crap.

Yep. Did the same to my cans. Those dang "safety" spouts are impossible to use and actually end up wasting fuel and make a mess if you're fiddling around trying to get it to pour. It's much simpler to literally just pour gasoline into your machine or car with a normal spout.

Those reviewers trying to get us regular listeners w/o thousands of dollars spent on HI FI gear to buy an outside DAC are not being honest, I got one to bypass my PC's gaming motherboard's built in DAC and honestly i could not tell the diff. I feel I wasted $150.

Thank you so much

Perfect timing 4 video! I was just trying to figure out y smartthings wasnt working and i go on youtube and u just posted this video. Thank you i was going nuts. Hopefully they get this problem figured out.

Do you have simple fix for a stuck bug or a ant died inside behind the screen

Thanks for sharing your findings, CO Guy. Question: when you take the measurement 8" directly in front of measurement #1, which circle are you marking/selecting in the software to indicate where you are measuring? There is a front right and front left circle, but not a "front middle" option. I understand where to put the mic for that measurement, I'm confused about what circle to select for that measurement. Hope this makes sense.

love the sausage dog painting xD

Thank you mate.

Where do you buy capacitor for year 2000 citizen watch? The citizen website doesn’t even recognize that old serial no or case number or model no

Would you have to reapply the petroleum jelly after some time passes?

Flavacal is the #1 plenty of coconut oil is also king !

Nice video. Curious, would you still recommend this amp (4 years later)?

for black crush on 22 point. adjust brightness level 5 good or can i go higher

I have two PB12 NSDs (not coupled) in my system, and I cannot imagine ever needing to "upgrade." Even using just one of them is really good. There is, for every category of audio component, a point of diminishing returns where the performance-for-the-money curve drops off sharply. For me, the PB12 NSD is right on the peak of that curve.