Video

I live in South Texas and just found out there is a whole slab of concrete about four feet under my whole five acre property. I have no idea what used to be here before, but it sucks. I had to dig about fifteen holes because my wife and I went on a tree buying spree. I used nothing but a regular shovel, but it took ages... Now I have to build a fence for my goats and chickens, and this is gonna be helpful...

Great video, is this the 10 or the 12"?

pain the the you know what? bro, try talking like a man will ya. Say ass.

Are those bacon wrapped frogs!?!?

Your using it wrong

pff, you us the tool backwards..

I was just doing this yesterday. I need one of these bars with the tamper end like you got. BUT ... I am just going to wait till I get a backhoe! Then I will use a sonotube and back fill after I dig. I am 59 and have a bad back!

ah yes, the perfectly round hole of an auger, and some sad act pretending thek know how to swing the wrong tool at another wrong tool... making the person look like a tool in the process....

Knipex are made so well that there is no wrong direction!!!

I still don't understand. How about showing me in west texas how this is done? lmao..

yep can confirmed they fixed the new model uses a ball retainer thing

Whats the real name of that Big Bertha tool? Need one asap!

I bought an auger with intention of building a rig so I can operate it without having to manhandle it (tried it once and don't want to do that again, almost ripped my arm off) but recently got land cleared and realized my land is very rocky. So think I will need to take another approach. I think for most of my structures I'm just going to lay them flat on the ground. Probably won't get much frost heave anyway. But for things like fence posts I will need to find a way to fasten them properly so that will be tricky.

How does the Klein compare to the Milwaukee.

I just got this thing and loved the concept. I used it for 2 hours of pulling tiny little clips off and the ball or clip flew out onto the weld shop floor never to be seen again. Very disappointing. Got from amazon so i dont believe the will warranty it. The chinese build quality really showed here.

Good lord that took a lot of effort. Smh😂

I am holding my own right now.

I needed a pipe cutter for stainless steel, I found the knipex cutter but wanted to confirm it actually cuts it well. Nice video

Thanks, Captain...

Can I have yours?🥺🥺

That seemed to take longer than needed to. Since you are just replacing it just cut it

Mine did the same thing the 1st time I used it...

Your Lower Part is not Secured tighten the Vise more..

i just bought this bag through their spring promotion and got the sb-ld free.

Some guys like to screw backwards🤷‍♂️

Aw I literally just saw a short right before this where the smallest one literally scratched the living stuffing out of a few fittings. I think it really depends on the fitting metal comp. They do make plastic and rubber grips for both the wrench and the standard so neither would mar.

Wrong direction. Amatuer hour

Thanks for this video!!!

The 3d printed inserts are nice to carry fewer pieces but more varieties of stuff

Fr dude you just have to accept it’s gonna suck and take a while😂

Bought one two weeks ago in the UK and it failed as you describe in the first day!

Bro.. you’re messing with the keyboard plumbers by intentionally using the pliers backwards😂

I got one second hand and not only was the spring gone but the bit was missing so I just took a 1’ Philips and I small piece of electrical tape and just made a new one but now it’s a 5-in-1

Your videos are amazing! If you like farming or harvesting videos, I look forward to having you visit my channel to have relaxing moments together!

They don't "lock onto the shoulder" when you're using them backwards. Hope you learned something

They have a revision of the 1505, putting a retention ball bearing on the bit socket. Available at Home Depot system wide.

Count the amount of turns

Marker works just as well, tape measure works better, but most can’t read one

What is the spike called?

I don’t know what was going on there, but as an ex plumber, it hurt me 🤕

You used the plier ok incorrect way. Video shows you are tighting up the screw. Turn it left for loosing down. Turn it right for tighting up.

If you are using grinder wrench, you shouldnt use grinders

Just got a pair of these pliers and they are awesome for what they are and money spent . I found them a little pricey but certainly worth it to get. I also heard that certain tools made in Germany 🇩🇪 are really good tools (although pricey) but good tools.

having KYB for 5th year with 50k on it, no problem at all

First off, you should have noticed the worn tire about 6 months ago. Ya must only drive at night. LOL 😮

A blown shock has nothing to do with the worn out parts or crappy alignment that is causing your tire wear. The only wear pattern a blown or missing shock can make is cupping.

Are these aftermarket shocks?😊

What other damage did it do? Ball joints, and tie rod ends need replacing. 🤦🏼‍♂️🤦🏼‍♂️🤦🏼‍♂️

A bitter memories of last week job

Saved three by repeatedly charging, finally getting full charge. Their are other methods, too.