Video

czcams.com/video/sQbLKbfnuwE/video.html Germany....

Tako je. A i problem su bili zubi. Stavio sam umjesto 3 na 5 zuba. Sam nemoze da ulovi drvo da bi zakocilo pilu... LP

@@mars-th8ci ma joj bjež mene je strah svaki put kad režem s motorkom, bolje polako i potrošit rezervoar goriva više nego brzo pa se poderat i svašt nešta. Čuvajte se i ta partnerka može dugo dugo da služi.

@@aldinnidla770 kupio sam neispravnu malo. Zubi su problem bili za tanke grane. Isto kao i na snimci. Za 5 gustih zuba je ok. Dok se reze sa pilom nema ni pive za mene onda... 🙂 Tek nakon posla. Budi mi pozdravljen, hvala na komentarima i sve naj u 2022.g. 🍻

Hello. Is not new. I clean and repair this saw.

Yw... :)

Great saw, not sure my neighbours like it tho 🤣

Pro trick: you can watch series on Flixzone. Me and my gf have been using it for watching loads of movies recently.

@Jimmy Randy Yea, have been watching on flixzone} for years myself =)

Hi. Yes. It is 12 inch.

12" Oregon 120DGEA061 chainsaw guide bar & 91PXL048G chain .050 48 DL 3/8LP. Im also replace drum to 27958 Oregon chainsaw saw sprocket fits 3/8. All pass fine on saw and runing nice.

@@mars-th8ci sweet Im pretty sure I ordered the right thing for my little xl2 I just restored myself. But if you dont mind me asking. I replaced all my oil and fuel lines and such . What did you do or use for the duckbill valve for the oil?

@@LaneSandelin Saw not give oil to chain?

@@mars-th8ci I just fixed it. The little perforated brass connector for the bar oil duckbill costs 28 bucks so I made one out of a pen tube and used a needle to perforate it so air bleeds out after I shut the saw off. I was gonna say theres no way that little duckbill can stretch over the oil line without a connector.

Maybe some new clutch springs and he could lean out the low side more and have the chain not move at idle? idk I'm just spitballing trying to maybe help a guy out (not an expert at all fyi)

Lmao.

@@MinusTheSparkPlugs To make it idle down you have to richen the idle. I can hear the lean tone, I just tuned one of them.

Low jet is lean..

Hello. Sure you can install 36" bar. But only for felling thicker trees... Recommended is 20" bar. Im not sure how is good working only with 36".

Gtc

@@svengulden7451 140psi Good compresion 372xp oem?

@@mars-th8ci Friend, if the saw 372 xp after replacing the OEM piston, the compression will increase? after a few tanks now it is only 140 psi after refurbishment

Yes. On IP: 85.14.228.195 port:7777

Well, thanks... I guess I have to get Unreal Tournament 99 again....

I give this saw for parts. She is not working. I just repaid saw and works good. :)

Right Bruno. All what you say is true. Ty for comment. :)

I watched other videos from you. Indeed you aren't a novice :) indeed you seem to have much more expertise than me on chainsaws. I'm indeed a novice since I have been using chainsaws only for 6 months.

Hello. 20" (50cm), 3/8" (72DL), 058" (1.5mm)

mars007 . Would a 24 inch be to big?

No... Wont be to big. That is strong saw and can runing on 24" for sure. I have 20" because I not need more big bar.

mars007 . Thank you. What cc is the 390xp???

6.5HP. I will set only big dog spike. Soon will set new video with updated spike and I hope first test cutting on wood. :)