Video

Yo man fuck the haters you do you, plz keep sharing shit like this, it helps people out

you getting burned down on that cylinder vid eh like im sure eveyone said - you can only fill the tank to 80% lol

I came here to comment on your 20 pound propane tank CZcams short video that you made. For some dumb reason you turned off the comments. Don’t like criticism? Propane tanks are filled to 80%. 80% of 20 pounds is 16 pounds. How about that? It’s not a scam. yes you might have found somebody to fill it. “all the way up.“ And that is absolutely stupid. Stop turning off comments on your videos.

I used T27 today, do you think T29 is better? I read online that T27 should be better for flat sanding.

You really shouldn't overfill a propane tank

Why you turn off comments on your other videos? Dont like criticism?

Great video! Really helpful. I have a 2016 HRV, would it be very different from this? The dealer already told me it needs to be replaced, I’m ordering my own parts and trying to do it myself to save some cash.

If someone fills your propane tank to 100% capacity it’s pretty dangerous. Propane tanks should only be filled to about 80%

Very informative. Thank you.

Thank s for putting this on

two types of shops, the organized or the full blown mess 😂

and where would you get it?

what size fuse is needed to the battery?

What if you don't have purple wire for steering wheel

NEVER touch those screws! (Unless you know what you're doing.) They are not there to adjust the distance from the magnet, they are calibration screws and turning them will destroy the accuracy of the measurement. Look at the graphic that is stamped next to one of the screws 1:40. It is necessary to choose the right reed switch that will not be too sensitive. Anyway, thanks for the video, it helped me with the reed switch replacement.

Thank you sir!!!! Well done and Much Appreciated!!!

So that will make engine light go off.

3:08 bless you

I have a question you first set it up the black mark was perfect inside the Groove then when you turned it 3 full times it was one link off that Groove at 35:30 into the video so it was like it was before you started the job. Why is that? Is that ok?

thanks for this video foreal helped so much

Thx. Appreciate review. Too many ants here so need some natural deterrent.

You are right, Thank you, bro👍👍👍👍🙏🙏🙏👏

Thought 5 minutes was too much just to learn how to tie a cardboard stack. Was totally worth it - perfect video, perfect knot for recycling cardboard.

4GB of RAM really isn't enough for an Android device, which is likely the main reason for the lag.

Thanks for the video but climbing the other tree tried to defeats the purpose of not having to climb so this would not work for me but thanks for the video

Thanks buddy

it just sounds like a hassle to explain to a cop if you get stopped. i feel it going to end with the truck and trailer getting impounded until they can verify what the interstate trailer laws are

You pop off the white locking clip on the solenoids and then you can push the locking clip with your thumb and it pops off. Also if you are doing this to get your check engine light off, do not erase the code. Just start the car and let it run for a minute, then shut it off and let it sit for 2 minutes then restart it and let it run for another minute and shut it off and wait for 2 minutes again and the 3rd time you restart it your check engine light should be off. Now your car will pass inspection without you having to wait for all the other parameters to reset to pass inspection or wasting gasoline on doing the drive cycles to set all the parameters.

Thanks Bro - You saved me from buying new to replace my 10-15 yr old trimmer! Runs like a top again.

Thank you for the information.And thank you for showing me how to do that.Even better than ever thank you very much.I appreciate it

Unless you get one of those expensive sharpening jigs, flap disc and angle grinder is absolutely the best method for sharpening mower blades.

Do you recall if the slide pin with the rubber piece at the end was on the top or bottom?

Bought a new transit 250 in 2021 and just turned to 40k km. The driver side rear hub broke! Cause the rotor damaged. Dealer ordered hub part took over one month and warranty coverage is an abusive argument. Stay away from Ford! Nice looking with very poor quality!

thank u sooooo much

Its not cheap , my father in law paid $1900

Good video, could improve by cleaning the grinder.

I have a loud squeak that comes from mine. I’m not sure where it’s coming from. It’s very loud, but it doesn’t always do it either. It’s weird. I have a little over 101,000 miles. It’s an 28 with 2.4 AWD too.

I like the bamboo

Not good, not terrible

Thank you so much for covering this! I feel like every time I bring my car in I have to make sure the dealer is doing what they say they are doing, every time I drive off the lot, I have to go right back again because the issue wasn't resolved....and I try to do whatever I can on my own. Where are you located? I wish you could be my mechanic.

I bought this kit and installed it last year and the damn Mother Nature hasn’t given any snow to test it out. I will report back when I get some actual snow.

Helpful 👍 🤜💥🤛

This is for the gmc 2017 and older not for the 2018

Nice job!

Excellent idea !

right buddy, i have all that stuff lying around in the house. not.

I hate timing belts !

THANK YOU THANK YOU THANK YOU!!!! Oh yeah... THANK YOU!!!

I bought running bamboo instead of clumping bamboo by mistake. This took alot of anxiety away about planting them. Ive heard horror stories about running bamboo, but im finding alot of those myths are extremely over inflated.

The materials on the description show R134A refrigerant but I thought these models used R-1234YF?