![Nick's Engineering](/img/default-banner.jpg)
- 4
- 71 760
Nick's Engineering
South Korea
Registrace 5. 10. 2020
[HYSYS] How to make binary equilibrium plot & table
[HYSYS] How to make binary equilibrium plot & table
zhlédnutí: 2 000
Video
[HYSYS] How to check water content/water dew point/Hydrocarbon dew point
zhlédnutí 5KPřed 3 lety
How to indicate water dew point HYSYS? How to indicate water content in HYSYS? How to indicate HC dew point HYSYS? How to indicate Hydrocarbon content in HYSYS? How to make stream water saturated in HYSYS?
Pump NPSHa and NPSHr \\ pump hydraulic calculation
zhlédnutí 32KPřed 3 lety
The pump hydraulic calculation is required for a process engineer to prepare pump data sheets, Control valve data sheet and to check pressure balance between each equipment. As a junior process engineer or university students, it is helpful for them to understand why they are doing those calculations. The purpose to carry out hydraulic calculation(especially for pump circuit) is to fill up the ...
Gas Dehydration and Glycol Regeneration Unit
zhlédnutí 33KPřed 3 lety
Gas Dehydration and Glycol Regeneration Unit
Hi, how do you monitor and confirm the concentration of TEG both lean and rich?
Please i need this process flow sheet
Sir, where will be pressure drop take place. Kindly explain that. Because from dehydration column rich TEG 30°C 30 bar, after the control valve suddenly the pressure drop to 5bar how, from where it drop. Kindly please explain.
thank you for this educational video ^^
Superb 👍
Very good for learning!
i have a doubt, how fuel gas absorb water particles
Wonderful Sir .
Excelent! Thank you!
Nicely explained 🎉
Very informative video. Thanks Nick!
Hi Nick , thanks for your support and my. Question is wether we can add or subtract the friction loss in discharge, I think we can add friction loss in discharge....
What do we do IF we set 99.5 % wt of TEG to be used as an absorbent in the ABSORBER COLUMN? Would you happen to have any advice?
I meant., how to SET at HYSYS v12.1?
P discharge should be p statuc plus pressure drop
Hi nick. Appreciate if you could do this kind of explaination on other system as well (fuel gas system, compression system, gas dehydration system, etc)
You have said 1 bar is equal to 10.2m but in NPSHa calculation you are mentioning 10.2m for 0 bar
In NPSHa calculations he has taken 0barg so that means 1.01325 Bara = 10.2m WC
Very informative ❤❤❤
1atm is 0 barg is that correct
1 atm is 1.01325 bar g
@@alagusundaramkarthi6605 1 ATM = 1.01325 bar A but not bar g. 0 barg = 1.01325 bara = 1 ATM
Addition of ∆P in Discharge pressure required😊
Hi, Mr.Nick How to know if the pump requires minimum recirculation line? I don't understand clearly. I have this idea that this minimum recirculation line is related to turndown ratio advised by vendor. Could you explain clearly?
If you study API610, you will find out.
Thank you for this video
Great. Thanks Nick
A very good explanation. Thank you Nick.
nice biriyani 😀
Nicely explained.
Thank you Sir for your super teaching and informations in this video... You clarified many points in my mind in the Gas dehydration Unit
u have whtassap numnber
Please help me explain where the Fuel gas flows when it absorbs water from the stripping column @all
Hi Nick. Thank you very much for your video. I have a question, if i put a pressure gauge at a suction side of the pump. If I substract the vapor pressure of the liquid from the reading of pressure gauge will I get NPSHA? Thank you again.
Yes, correct.
Thank you for your thourough and excellent work
Thank you
clear and detailed lecture. thank you.
Very nice explanation, thank you
I love the way you explained the whole process and broke it down to a layman's understanding. Wonderful, I must say! 👏👏👏
Kim Jong-un
Any video to explain gas dewpointing please
Hi. If we have pressure gauges on an existing system on the discharge and the suction, we can just look at them right? We don't need to calculate, am I understanding it correctly?
Thank you brother. Very nice ❤❤❤
Please share more
Haha thanks
Very nice explanation brother ❤
Very nicely explained in a simple manner, I use it for training junior operators. I request if you can do one for gas sweetening.
The water can deliver at 50m Head from a pump, if we can use glycol instead of water in the same pump. Is any variation in head
The Head is the same assumed that the viscosity and pump speed are the same. of course, the denser fluid will affect pump efficiency due to hydraulic friction loss, motor power efficiency, etc.
Is NPSH calc applicable for closed loop systems? I only saw open loop examples and nothing for closed system
Hi all, anyone has an excel sheet for pump sizing they can share? Thanks
There are many sheets on the internet. You can easily find but you need to verify its calculations.
tnx good
Thanks
Hi Mr. Nick !!! Greeting's. How come vessel operating under atm press became 10.2 bar G pressure in your calculation?
so good thanks
Good day sir. I really appreciate your video. I was wondering if I could contact you and ask a few questions because I’m considering doing something like this for my final year research project. I saw somewhere that nitrogen gas can be used for the stripping of almost lean glycol and I wanted to ask if other mostly inert gases like co2 or Ar could be used in the stripping column
Iam now Fully understand how this system works iam new to oil and gas, your explanation like a professor. Aneongaseo