Video

Hi, could you please tell us how much money has gone in to this? That is excluding the plasma cutter :)

Well sir, you put the work in, and you're thinking all the while, this is how it's done right. If it was me I would knock all the rust off I could and coat all the steel with por 15 to prevent further cradle rot. Because cradle rot sends cars to early Graves, front and rear, every time. Hard to pass inspection if there's nothing holding the undercarriage together😂😂😂😂 but great work man!👍💯

Can I ask please, what is the total cost for this build? :)

Nice... Hard Grind Plumbing like to integrate lots of hexagons in their builds... It's a strong shape, both mechanically and visually...

Castor and camber is in the spindle. The an arms should be level. And have appropriately 3 to 4 degrees negative caster with a small amount of positive camber maybe 1/2 degree or so have fun kids building your dreams

Make sure you use the old arduino 1.12 and not the 2.0 version .arduino won't flash to latest version .

How much did the 3D printed parts cost from JD's Garage?

Love the project and attention to detail. Really dislike the music that's 25% louder than the spoken words. Volume down, volume up, down, up, down. It's as bad a commercials on TV, sorry...

I had this same exact situation on the back of my Grand Prix. It was so bad I was thinking of selling the car. Fixed it. Thanks man!!! Got it aligned and she runs perfectly. Almost like a new car.

What plasma cutter do you use

only issue I have with these generators is they kick out due to how system is grounded ,which is what yours has done in video ,, red light on . once you fix the ground on them they will run almost anything you throw at them

Thank you for sharing. How is the machine holding up? And can you share what your air compressor cfm rating is?

Any video update of the Cnc plasma, did you ad the z axis ?

My G6 had a broken spring & every little change in the road made the back of the car leap off of the ground. It was pretty scary. I found 5 wrecked G6 s in a pull a part salvage yard & all but one of those cars springs were also broken. It must be a Pontiac defect.. just like being notoriously known for having bad ground wires that don't look bad! There is a great video out there showing those bad grounds being on the drivers side motor.. which codes TCM

Just got mine yesterday. My model is LTP5500DCNC. Hopefully, the CNC designation indicates the updating of the original D to a more CNC specific configuration.

Wen u put a electric fuel pump on did u have to put a fuel regulator on aswell?

Hello, again. I'm at the point I can't delay the wiring any longer as I have done all the mechanical elements including the Z axis feature. My question today is do you think I can put the Z driver in the ammo box without crowding things too much and creating too much heat ? I was a little unsure of how much wire to use on each run between the drivers , power supply, and the other small elements in the box but it appears all I need would be just enough to place the items neatly on the board. Thanks , as always, for your insight Demon

Looks like you ran out of loader poop, if it had been a stability issue (lift the rear end up) extended that hoe out would have helped. I had a similar tractor hoe setup, and as a big crane operator, I enjoyed having having what amounts to a movable counterweight!

I love old engines..

How did you build the cutting surface(rack)?

what do you do so that the frequencies do not interfere with your electronics

Tell me you bought an ammo box from Princess Auto without telling me you bought from Princess Auto. ;) I'm enjoying your build, excellent

I built the JD's Garage table myself and it looks like maybe you had the same problem I had. That would be that the torch starts to move a little too quickly after the "Torch Off" command is sent. This leaves a partial slice when it moves to the next position. So I "hacked" the post-processor and added a time delay right after the M5 (Torch Off) command. Now all the little slices are gone. I just basically made the "leave" delay equal to the Pierce time. I was doing this "by hand" when it first started but later figured out how to change the Post-Processor to do it for me. Less time and less mistakes. Next I want to have a Laser option . . . Happy Cutting!

Hello, again. I just wanted to ask you if you are happy with the plastic ammo box for the electronics. I have the same box you have and I am at the stage of starting on that part of the project . Do you have any issues with heat ? Should I add a fan or is the method you show in the video working fine. Thanks for all your help.

Love the thinking outside the box , got to do with what you got when they don’t make stuff for 50 year old machine

How much. Did it cost to build

Idea on making those washers a bit easier to install. On the stl files, add a extended bit. Instead of being shaped like an O, it would be shaped like O- so you have a little piece to keep ahold of while installing them. Then trim the piece off after install

I've noticed that there is an issue between USB 2.0 and USB 3.0 with serial comms. Most outputs on laptops these days are USB 3.0 due to their speeds but the pin outs are just a liiitle off. Not sure why it doesn't work unless it's a serial USB cable issue, but I'm assuming you're using the same cable that came with the arduino. Glad you were able to work through it. This is giving me inspiration to try my had it.

What software are you using?

What cutter+compressor combo are you running with the table? I'm about to start my build -- parts are printing right now heh

Hy.helo.man.this.c.n.c.machine.what.cast.u.s.dollar.please.tel.me.again.i.like.it.by.by❤

Helo.helo.man.your.anser.some.one.like.❤I.like.it.love.you

Hy.helo.man.i.very.very.very.like.like.like.this.c.nc.machine.your.manufacter.i.love.your.this.work.gOadby.bales.you.love You.by.by.form.zahid.inam.pakistan

When your not using the cutter, maybe the arm should be supported. That would take stress off of the 3D parts.

Great videos! It might seem like a silly question but what was the stuff you sprayed before etching on the metal in the first minute of the video? Just paint or something else?

You did a very nice job on this build. I’m about 90% complete with mine. Your shielding wire did you connect it to the motors or did you just leave it inside the wire? Thanks have a nice day.

good job. thanks for sharing

Nice to see one of Nate's calendars on the wall...lol

Buenos dias, disculpe si podría ayudarme con el listado de los componentes. Seria de mucha ayuda

Thank you! this video has helped me a lot!!!

hello, I have a similar idea. How much are the engines pulleys controls etc. All the things to make your machine work from the motors on. Thanks

Hello, again. I hope im not being too annoying. I am going to use the same plastic ammo box you did. Can you tell me what the fittings and glands you used on it ? Also, about how much of the 4 conductor shielded cable did you end up using ? Thanks.

Thank you for sharing! Could I ask where you bought all your bolts from? When I priced all the bolts and nuts as per JD, came out pricey in Canada/Toronto.

Nice work, just finishing my table and looking forward to some cutting

Very clean cuts. looking good.

There are several people who have this exact generator hookup to their house, food trucks. It works for them. How can this be? It doesn’t seem logical Briggs would put out a production generator that will not work . Mine works fine.

Hey dude. I'm in the process of building this table. I've watched your series on it a number of times ( I'm a bit dense and it takes a few exposures to new ides for Me to absorb it ) . I have , also, lengthened the legs, am going to casters on as well. Today I assembled the bearing blocks . The first one was a bit*h but the second was much easier ( washers ). ANYWAY, now that you have been operating it for a while, do you have any advice as to pitfalls I might encounter ? BTW I bought the same ammo box from Harbor freight for the electronics ( really not looking forward to that ) And REALLY not looking forward to the flashing etc to get it to work as I don't have a computer guru buddy to help. I'll shut up now, Thanks Demon

It very satifying to watch

I built a front end loader for my Deere 420 this spring and I cut out a bunch of stuff by hand. Sadly it looks like a little kid did it. During the project I was wishing I had something this size just for brackets and small stuff like what you did here. The FEL worked great for the projects, and I keep finding stuff needing it. Now this fall we got a couple rain storms and it appears I need to dig up the foundation on one side of my house to find and fix a leak. Well now this spring I'm going to build a mini backhoe. Thinking about my experience with the FEL, I started trying to figure out what I could do. JD's garage popped up in my research and now after watching your build..... Next paycheck the plans and 3d Printed parts will be ordered. By super early spring I'll have the table built just in time to build the Mini-Hoe! If I'm smart, I'll figure out how to use my Go-pro and other camera to actually video both builds. LOL Great job with this!

Seems pretty fast cutting holes, and I know you have the same cutter than I have :) But mine are not getting properly circled :(