Video

I've tried heat, penetrating oil and brute force with no luck. Gonna try this next.

What was wrong with the lower control arm? You didn't elaborate

Solo suelta los tornillos del alternador.

I see that you loosen it but not how

I'll install it in 5 minutes

Wtf do do with zip ties. Worthless video

You showed nothing of use

Jackass didn’t even show the most important parts😂

Thanks ❤❤

That’s a very nice bed thanks for the video

Great video! Im having the same troubles no power no crank or intermittent with security light constantly on. I’m trying to figure out what key I have but can’t get a reading for some reason.

What brand are the upgraded axles

Wtf you can’t even put it on

It's 23 years old Looks pretty good to me

Yup I’m having the same problem on my 48re to lol I’ve tried everything gonna try this now

Garbage cars stay away from any Hyundai Kia products

Would have been a better video if you actually did something instead of just talking about it.

One of three things a b c coil or valve go bad

I have a 2002 24v 3500, bought it wouldn't go into overdrive. Replaced the transmission still no overdrive. I've changed batteries, grounds every single speed sensor including in the rear end. It has to be a broken wire or pcm. I'm so discouraged it's unbelievable.

Link ? Nothing 😢

I ran into a problem like this several years ago and couldn’t figure it out. Thanks for the information. Next time I’ll know what to do.

What was the issues. I m having a problem. Replaced thermostat. Sensor. Waterpump. Radiator. Leakage test for combustion good but the car still overheating up and fan runs non stop high speed. Guys i need help.even swoped fans still same. System burped properly i dont know what to do anymore even considering selling it but i love my jeep Sahara just bought it 4 month's ago after saving quite a while to get one one. Please assist

Great video on the E47 Meyer pump / I wish you could have actually shown the testing for the b and c coils / for those of us out here struggling to understand this/ Thanks from Jersey

Is this truck easy to work on?

what if you pull out all four sparkplugs on a seized GDi engine and it cranks "TURNS" just fine?. but when you put them back in the engine locks up.

That's for showing the socket size

Congratulations; you have won the award for the absolute worst video on the Tube.

When did the upper rad hose blow off? Asking for a friend

😇 'promo sm'

I'm still on my original set of plugs in my accord 256k miles still going strong on this experiment

Wish I had this truck

Can this make produce a smell to come from the vent inside the cab?

I'd pay good money for this

A resistor is not a chip. Go turbo.

My kia optima just seized 3 days ago But The Local Kia Dealers told me that they will replaced for me free of charge and they will pay for car rental for 3 weeks that my casa 12/18/23

More reason to hate these problematic trucks.

Great idea

B is up and A is down

learned this is a thing this morning. Ive beed needing new axels every 18 or so months since the cv boots are always being torn to sheds. Took my lifted silverado to a new mechanic and he enlightened me. Not cheap at $378 ea but hopefully this issues is now resolved for a long time

Thanks for the video. I just bought the same axles. Have the same lift and issue.

This angle is too large

You would never want to cap the bottom of those rear bumper supports. They would rot out in no time without a way to drain. Condensation builds inside of tubing and if it can’t escape it’s guaranteed to rust out whatever it’s sitting in

I believe the OEM Mopar thermostats are on national backorder. The aftermarket therms are junk.

Do you think I can mount a 12000 pound winch between the grill and the front of the bumper I don't want it to stick out the front

Insightful video! I really like the straightforward troubleshooting, like using the laser temperature gun to double-check the temperature-sending unit.

Worked like a charm (6.2L though) Just should have waited for the truck to cool down first.

How much is it going for ?

Have a recently rebuilt e60,not by me,the lift ram was supposedly rebuilt...it makes a awful noise when it's %50 lifted or more....never in my life have a heard a plow make the noise this plow makes.i think the ram is binding inside the sleeve.....after one or two cycles the ram is warm to touch...I'm going to open it up tomorrow but Im hoping it's the ram washer and not the pump gears vibrating inside the housing

I torque it down as hard as I can with my 4way tire iron 😎 after impacting it on setting two with my Dewalt high torque impact wrench.

Ahh! One of the reasons i started doing my own tires....