Video

I didn't understand well enough, unfortunately.

Muy bonito su video ingeniero megustaria saber si tiene un proveedor de refacciones para este modelo de bombas le agradecería mucho

J'aimerais me joindre à vous pour un éventuel poste de mécanicien industriel a pouvoir

I noticed that there is a rise in the suction line immediately before the pump. I’ve always been taught that the suction must always be rising. Can you explain why this is not always the case?

merci tonton tié le sang

Nice demo, thanks!

Great...

The best. ☝️🍋🍸

The first time it draws water, then it releases water, why then the pump quantive runs, it gets hot, please tell

Pls hindi translate

No head preasure

P❤I

Excellent presentation, Joe. That IS precision inspection.

15 to 20 thou on the wear face is a given in the pulp industry, mechanical seals suck!!!!! packing is so much better!! 8$ dollars vs $5k dollars for saved water....

How bout when you have a correct mesh size even then you think the strainer will cause problems

When i checked the shaft runout, i take several points along the shaft, start from coupling end to impeller end, checked the surface condition if any damage on it.

When this is installed do you have to adjust the wear plate?

This is really great, well presented, I bet that guy could easily fill a book with all the knowledge he has.

Surprised there are not more comments

What is the empty hole between the shaft and drain??? Hole above seal cavity drain plug.

This a well designed assembly. Kudos to the design and manufacturing team. Any comments from the maintenance engineers among us who have service this type of pump?

Great video buddy

Sarah is drop dead gorgeous <3

2 relays relay 1 relay 2 for output.. how to change its contact type default setting NO to NC...

Ribs on the reverse side of the impeller increase strength, but when pumping abrasive water-sand mixtures, this leads to increased wear on the back wall of the pump casing

This is so helpfull

Dear sir, Good morning how are you?? please advise me. explain how to change the oil cell? Best regards, Wasi

Sounds like all might

???????

Thanks guys I'm working for the first time as maintenance personnel and these videos are helping me kill it

Good

Beat pump series.

The music is distracting. The parts on the white display(?) board show no individuality for identification. All the parts look the same. Perhaps this video was made mainly for professionals.

czcams.com/video/dUBjCQ-FSq4/video.html

Durco Pump Parts -We manufacture multiple pump parts of ANSI, Goulds, Durco that follow the American National Institute Pump Standard. Contact us today! mosherflopumps.com/pump-sales/

Good

Bad rally bad video

The gentleman says to use a shaft parts kit when the radial bearings are out of tolerance but the caption says when it is NOT out of tolerance.

Yeah, it’s that easy to pull out when it’s brand new without years of gunk jammed up in there.

I have a Gould's submersible pump for the water for inside my house. It's an older one an old.man gave me. He said it can be repaired. The motor runs strong , but the fans or impeller dosent work. Can that be replaced since being the Gould's are so expensive and I need a pump for inside my house because mine quite working.

My cartridge seal is on a sleeve from new. Similar to this one in the video but has a sleeve in the center of cartridge and does not fit on shaft... do I have to remove the sleeve?

Great

Not sure who else to ask but you seem very knowledgable. I'm using a 10" Gorman Rupp self priming prime air pump in a creek that has a huge pool area that I'm pumping out of. The pump primes itself easily but when losing prime, it cannot reprise itself. We've done this many times but never had this problem. The pump will actually pull the water right up to the pump but won't pump. Any suggestions?

i need repair kit please do you supplier in egypt

Can you please do a total breakdown and put back for the gt10?

For AC centrifugal pump with a fixed power supply frequency (eg. 50 Hz), if the NPSH required is achieved, is the flow rate constant? Is the liquid flow rate at the rated flow rate on the nameplate?

00923333679286 whtsapp

Gracias amigo me sirvio mucho

Sir how to download PDF file of pump curv