Video

Nice setup. what is typically the best bait for flat head?

High low rig is even easier & does the same thing. keeps bait raised off the bottom a little bit.

Been using a similar rig to that for the last 55 years. We typically put the swivel on the loop for the hook and we never tie a knot on the loop, we just run the loop through the eye of the swivel, and then put the swivel back through the loop end. The Hook can then be taken off the rig for safe transport! Your rig is fine, but looks like a LOT of extra work to get the same thing we use. Most of the time it's the hook that snags/gets hung up and with the swivel on the end of the loop, you lose the hook and not the lead sinker, rather than the whole rig.

that's pretty neat but what do you do in the case of snaggs does the swivel just snap or the hook or the sinker and is the swivel the weakest point of the rig or is it the knots just wondering if you had to deal with that and how you handles those

I just got a 1752 bare mod v boat. Bottom is beat up. But my 22 predator swamp runner should move it okay right ?

Very cool, I'll be trying this soon. But seems like this is best for braided line, not for Mono...? I feel like the knot that creates the "drop shot - 3 way" would be a weak point on Mono... one way to find out I guess.

What rectifier diode is being used?

hows the 500 held up?

lol. I'm the dude with the orange Crosstrek.

Was curious to was the setting was on the tachometer and how many wraps? Thanks

DuroMax dog killer

Thank you for making this video! Any chance you have a part number for an upgraded flywheel that outputs more power?

in have a 10ft jon boat also i welded a trolling motor mound to the front and welded a bracket for a 12 inch light bar i built flooring for it with carpet and i have a 6hp jhonson with it the weight really levels out with it

how did you hook up the throttle?

Is this the same engine that had the surface drive on it? What made you swap?

Always been a favorite spot on the river. Nice catch! Like your rig too! Thanks for sharing

Amazing catch of those fish 😎😎😎👍👍👍👍

@11:50. Why can't you just push down like a long tail to pop it out of the water? Oh and how fast with the 2 of you?

Still running good ?

for 80 so dollars u get that thang rrrrrrrrrrrrrrrriiiiiiiiiiiiiiiipppppppppppppppppppppiiiiiiiiiiiiiiiiiiiiiinnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn

Interesting you caught that huge fish on a small 'salty'. Just shows that it's not always the big baits that catch the big fish.

How do I do this if I have a thumb throttle

What bolt where you able to put on the shaft? the one provided was too small for me and idk what bolt to use

What’s your Top speed with this set up sir ?

1030.. 1032.. 1036.. 1040.. ALL 10 Ft JON BOATS.. BUT WHAT IS THE BEAST..?

I have a different regulator/rectifier, the one that has the red, yellow, pink and green wires. I know the red and green wires are power and ground on the regulator/rectifier. Does the black and red wires from the coil both go to the input wires on the regulator/rectifier?

Nice job brother! I got to make one of those!

the "sensor" is your electronic fuel shutoff for the carb when u turn the key into the on position not starting it you will hear it click after you turn it off it disengages. ik im late to the post lol but for anyone wondering in the comments

What torque converter did you use?

How do you like that duromax ? I just got my 14-36 with a 670 swamp runner on it. I built the transom heavy 1.5 thick aluminum and 1/4 plate covering most the back and another top channel that goes up the top rails and rivets down. Bolts through back got the weight set so It does good in the water but my question is, is it okay to leave the motor on when I don’t use it on the trailer ? Do you guys ? Like is it okay structurally like have you ever ran into weight bowing or denting pushing floor you were boat meets bunks ??

if you dont mind me asking, where did you buy the bike frame? I've been searching for alot of stuff but there not big enough. Please and thank you.

The farmers or someone else may have tired to blow it up sometime before 1993 flood, but I and uncle was looking at the dam from the road tresel Bridge directly across as a debet in the water line showing .mas amont of water pouring over top with me pointng at it when the dam blew , we ran from from the spot ,seeing part of concrete dam being pushed our way by the burst of water. I can never imagine a flood bigger since 1993, the flood covered the road west of bridge, we had to take a dirt road to get to west side of dam.

Your rod and reel

Where can I get one?

What size coat is rumble bee ? I know 15 feet but floor width ?

One thing i learned when i was growing up is that you dont need to go fast on the water. Id rather soak in the beauty and splendor of just being on the water. My Dad's friends would always laugh at his 25hp Merc. on his huge fishing boat. It got us there 10 minutes later and who cares how fast you get there.

THE BUSHING CLOSER TO THE PROELLER IS EASIEST TO REMOVE... THE PROBLEM IS WHEN YOU NEED TO REMOVE THE CENTER BUSHINGS... THE ONLY WAY IS TO REMOVE THE SHAFT FIRST AND HIT AND PUSH UNTIL THEY COME OUT... SAME AS SHOWN IN THE VIDEO...

It sounds like a generator engine whit a turbo on it.

Does it vibrate real bad or is it comparable to a 420 in that aspect?

Does the same intake for a predator 459/420 also fit this engine? I’m considering buying one. I have a 459 right now but I’m about to take it off my surface drive and throw it back on my longtail

What size boat? 15?

I found a 10 footer on fb marketplace and was wondering if it was big enough also that’s one hell of an intro

is the type where you just press the start button once and it starts, or do you have to hold it?

How did you run the throttle cable with the electric throttle it comes with?

Thank god you did this video! If you wanted to just do only throttle would you just direct connect the purple and yellow to the red and black?

What do you think of a 14-36 with a swamp runner 670 ? Maybe with float pods.I don’t want transom to break because the bottom corner has been welded in past but it’s got a TBN aluminum 1.5 thick transom. Two floor to transom triangle braces in it already then I got a 36-14 1/4 aluminum plate bolted through the back and transom. You think it will hold up with rough roads and the weight ? Hope to hear back !!

How did you re enforce that Transom? I plated the back of mine with aluminum and bolted it. we will see how it does

What rpm are you turning to get 18mph on the 224? Governor removed?

I have that same go kart I’m trying to fix up and I’ve been looking for seats where did you find the ones you have there

Is that a jackplate that you bought or fid it come with it