Video

i am trying to find a video that show exactly where to put thr Strip seal

My machine has quit exiting the air. I’m gonna try and clean it.

I tried to watch this through the link in the app, but the ridiculous klaxon sound was going off throughout. Quitting the app, or going back to stop it closed the link to the help guide and video. 😖

head doesn't stay in. brand new. junk trash.

why are you stealing videos from other channels???

I keep getting an error calibrate again when I click updating calibration. No customer support to help.

Hello how did you put the Lazer down

Hello! We are having an ink out error but we tried this method with no luck. We pressed the ink button to unlock the carriage and then when we press the button again it doesn’t do anything. Our main printer blew a board and have been waiting for it to arrive so we we’ve been working tirelessly for days trying to figure it out. We are drowning financially and really desperate to get it working. We were thinking maybe a firmware issue or maybe something with the ink volume control board thing..our other printer doesn’t have one of those so we aren’t familiar with it and can’t find any material on its usage. It has a little blue button on it and we aren’t sure what it’s intended for or how to properly use it. We have regular dampers with no chips… if you could please help us we are desperate. We would be forever grateful

Where do you find that software. All I can find is XCS on their page.

This does not work. Mine never says it's ready!

What OS are you using

could this be used with UV prints?

Has anyone fixed the optical sensor? This thing is an aggravation. It's supposed to free you up to do other things but I have to stand and babysit it or it will reel the film and a pile of DTF glue right into the oven. I have cleaned the sensor with sensor cleaner and antistatic. It works great for less than three pages then it's off to better off doing it manually land. If anyone has the actual fix I would be eternally grateful!!! Right now this thing is just a POS in my shop, not earning it's keep. 🤬 ~Please forgive my cross post.

This is exactly what i needed to see, thank you for the clarification.

Bonjour, cela fait des mois que j'essaye de mettre la caméra à niveau mais rien ne j'ai fait appelle au service technique du site et rien, pouvez-vous m'aider quand j'appuis sur process j'ai une fenêtre qui indique exception:illegal input!

this is a very silly video. I come here looking for assembly instructions and you start the video in the middle of the assembly?

"perfect spray pattern every time" hahahaha

worst purchase I have ever made. Constant problems. If i get a month with no issues, its a miracle.

do you have to wait for the printer to tell you when to replace? it currently just says near end of life

This is amazing!!!!

Hello, this is very helpful but the water pump is not is amazon or eBay, any place where can i buy it? I need one sap

A DVD SHOULD HAVE CAME WHITH THIS DON'T WAST YOUR TIME OR MONEY

This is a Wast of money I have this Printer All kind of problems I will be getting my money back Whoever Reading this don't wish your money

Pretty useless not seeing it WORKING. Was going to buy; but I hear ot does not cut well off a roll. Goes out of alignment.

How I buy this product ? Please help

It is very inconsiderate to upload 200 videos at one time. I am on my phone, looking at my subscriptions and I have to scroll for days to get past your videos. I am immediately unsubscribing.

Bonjour, Comment régler vous le focal je n'arrive pas à utiliser lightburn avec ma p2 .

Where can I find those clips to hold the hat in place ?

When you litter my feed with endless videos, I hit unsubscribe.

I’m having issues when I’ve cut the media and it feeds into the powder at the end it folds in on itself and then when it comes out of heater the last ones don’t cure enough and get stuck to the previous ones

This video beyond helpful. Thank you!

Hello, I just watched videos where they say that dust or glue that sticks to the design can cause cancer. What procedures should be in place to prevent this dust from spreading throughout the work area?

My ES mat keep wiggles when cutting some shape any hacks?

Where do you get your patterns from

Hello, what is the delivery time of the machine?

Nice job but you forgot to show how the smaller mats work with it to. No Dick tonight

*I Print a White Underbase even on a White Shirt. It makes the Colors Pop.*

Mine won't lock the new blade in place its loose

Hello , Can you use engrave a new laser design on a screen that already has a design?

how to I add the sleeve option to garment creator

I haven’t trusted her since this printer

Does this work with the f3070?

I am new to embroidery machines. I just bought the Brother SE700 and cannot find a video teaching this machine. Brother is supposed to be a good name in sewing. Why can't I find a video teaching this machine? I have ADHD and learning can be difficult. So seeing each step makes it easier for me to learn. Is there a site I can go to learn how to operate a SE700?

Can this machine do patches for hats?

wish someone could do a video on this machine show how to start the embroidery i lost 1 eye to cancer and reading is hard

How much

the video is blurry, can't read whatever he is clicking on.

Awesome Thanks for sharing this information

dose this digital factory v10 run on a Epson xp410

I’m buying one