Video

Would be good (for people like me) to remind people to disconnect the battery.

The idea of working on cars is great until you actually go and do it

Bro put back that k and n lmfao its cleanable lol and wayyyyy better then that air filter you just used smh its resuable

Great music!

U fk, dont do that idk how you did it but you couldnt your selft show it

wow i didn't know that x5 is more complicated than x5m. nice vdeo

yo can you generate a code for me

Exactly what I needed, thank you.

Hey can you post the link for the grill?

aah gud ol days with the greatest game machine of all time.

Hi, does your vehicle have AUTO HOLD? If yes, how do you ensure proper calibration when replacing the rear rotors/pads? Thanks!

took me 5 hours but i did it

Great video.

Hello Shezi. Thanks for the video. But i were wondering. Can you change date in bimmerlink for the next service? For example. I changed the motor oil in my bmw and i want to ”reset” the service so it shows up to me next year. Greerings from sweden

My advice to you’all engine oil is cheap just buy the oil and tap it up😂

Any tips for i4 G26? I have set all speed-lock functions to non-active but still not getting to video in motion!

🌟Thank You!! 🤓

Do not lower vehicle with under inflated air springs. Deflate and inflate with vehicle raised. Remove compressor fuse, use a scan tool or crack lines at valve block/compressor to deflate air pressure. Remove tire. Remove air spring. Replace fittings or be very cautious to reuse because brass is soft metal. Tighten fittings. (Side note, compress the air spring by hand and use soapy water to check for leaks at fittings, air spring clamps or bag itself.) Install air springs, route air lines properly and install compressor fuse. Place tires on. Let vehicle inflate air springs while elevated. Air springs can damage if set on ground under inflated. There are pressure sensors to prevent blow outs btw. Set the vehicle back on ground and enter ride height for adjustment or each side may be higher than other side.

Great video on this tool. Does this tool assist with bleeding brakes? They advertise ABS Bleeding on the 7360.

Excelente, solucioné el problema 🎉

how did you change your lights?

Can you use bimmercode for free on both iOS and Android? And would it work to disable stop start on a F16 BMW X6

will this work on any BMW 2016 or below?

im so scared of spinning a bearing thay i been putting this off.

This such sad how companies mading car radios and making rules and contracts with app companies just for the business.... Can't watch CZcams because of safety of driving that's right it make sense but they didn't make enough job to secure that because people found easy way how to hack this as the priorities number 1. For safety should be the easiest way to set up any car devices brightness and dark themes and maps dark moods (waze , goggle map's and others) ... But is so complicated can't switch my Google maps to dark mood also waze after long time searching I found how to do it but every time when I need dark mood need to connect with cable to my radio and do some settings to make it work at least Google maps... When I disconnected cable and connected back I need to do again play with settings and switch to dark mode sometimes it works sometimes doesn't .. is so complicated even with this video I was following all steps and it still didn't work.... Also I have dark theme brightness on lowest level and is still so bright where is here safety when brightness from radio flashing to the eyes at the night ? That's should be all Iligal so unsafe but good for businessesmans that's why I will have to return already my second radio because of dark themes, brightness, dark mode maps problems .... Authorities should stopped to be focuse on their business wake up and setup the roles about it no one should be allowed to open factory production with car radios till Safety problems not going to be fixed Thanks for the video ❤️

Didn't work at all on mine

Hi Shezi, do you recommend going to iridium plugs on a 2015 VW Jetta 2.0L gas sohc.? I was having engine misfire & flashing check engine light sometimes when I was driving and accelerating, so I replaced my spark plugs, spark plug wires and ignition coil as well. Instead of putting in Bosch FR7HE02 which I saw in couple of youtube videos and which are Nickel plugs, I put in NGK ZFR6FIX-11 which are Iridium plugs, Also I replaced the wires with Denso Ignition wire set and Ignition Coil with NGK Ignition Coil. I don't have engine misfire or flashing check engine light anymore but I can hear like a sparking sound after some time when the engine starts. Do you know where I went wrong? Also in some videos they say the recommended gap is .043 but this video says OEM gap is .032 I'm so confused because I ordered the plugs with a gap of .044 Please advise

I have a question. I swapped the nav unit in a mini year 2013 because the old Nav would not work. I ran an update using im608 pro from Autel. Looked like it coded all the modules in with latest software only the nav unit still doesnt work. The display works, and the radio works etc etc. The nav unit doesnt show maps though. I believe I have to extract the FSC codes from the old nav unit and write them into this unit. Does anyone know how to do this?

if I don't have sport plus mode in my f15, will it work on simple sport mode with traction control ?

Thank you for this video, but I have question please: is this value works with F46 also ?

THANK YOU !!

THANK YOU !!

Isnt it 100Nm like ista says?

Would this be able to register and code a battery? I need to change battery type and AH rating along with CCA if that's needed. 2005 E60 525i

Good ,thanks.

Thanks for sharing. It’s not true that you have to replace the brake pad wear sensor with new and it’s not true that it measures the mileage. On some cars there is a service counter for brakes which can be reset, but not all cars have this and it’s not the pad wear sensor that controls this. The pad wear sensor is merely a circuit, think of it as a switch, which is only made when the plastic is worn down by the disc and metal then touches metal. This is what brings on the pad warning light. If the sensor is intact, no need to replace with new!

So at 4:58 took you an eternity to push those clips and cut the video? 😂😂 czcams.com/video/-krslrOxcHU/video.htmlsi=LU3uI9r707n0o96K

Thank you ❤

Hi, can this delete Passat b8 error code dynamic road sign display

Can it be used to generate FSC Codes in order to enable Apple Carplay for NBT EVO id5 and id6 ? Thanks !

Hi what the best adapter to use with the BimmerCode

Could this delete transport mode?

Hi, how about torque?

I just got one of these for my Honda. Why only 3 icons across? Mine is the same. EVERY OTHER picture I see of this model shows 4 icons across. Just curious.

Thank You, this is very helpful !!!

Fucking legend

I got cbr 929rr fireblade and for the first time yesterday it keeps stalling im havin a lil oil leak wit coolant liquid as well...what could b the issu???

The real trick, is to torque the nut to 60NM while holding with a torques wrench.

Yea but now theres no fan to cool my cologne:)

Great save me a 110 mile round trip to the dealer !!! Worked great for my 2024 m240i