Video

This is super helpful! But sadly isnt helping my situation installing my new tronicworkz headlight harness. Im wondering where the plugs on the inside of the car would go. Also, so you need a whole 'nother harness for the fogs?

well.. i only came to see how to do the lower driver side, but you skipped it.

Good looks bro

How does it work with launch control

It was the cam shaft seal huh? It could be the o ring, but the cam shaft seal next to the distributor tends to lwak

The JDM integra has fog lights integrated into the headlights

Did you have to grind down some of the trailing arm to get the calipers to fit?

The box being near the shock tower. Isn't it too hot near the turbo which gets pretty hot under there! Is the box okay with heat near it?

Sounds great 👍

Can you provide an update on the lights and how they are holding up? Heard the housing leaks on them. Thanks!

It's always the random small channels that have exactly what I need. I may have bought factory fog lights, but man, you saved me hours of headache. Thank you!

What sandblaster is that and what did you use. Aluminum oxide or just sand

@JackWagonGarage How did the handbrake feel after this mod? I thought you have to replace the emergency brake too?

Not sure if you still check this, or if you've already found it, but the other end of that brown connector is up by the clutch pedal, immediately after the harness comes inside the car, almost right on the fire wall.

Great detail and explanation to install this conversion. Thanks bro :)

you said LSD installation. You did not show it going in. WTF

Is this a felpro gasket?

Did you find that your hatch stopped working when you removed the antenna?

Do you need to tune the ECU?

what test pipe is it i want to buy the same one

What bulbs to the fog lights use?

Could you tell me where to buy these harnesses ?

A bit off topic but i was helping my uncle build a subaru for my cousin 02 wrx 5 speed, we put a jdm version8 engine wire harness is from 2004 wrx but automatic, everything is done accept the is no connector for the speed sensor from the 5 speed is there a wiring diagram i can use so we can get odomiter and speedometer working ? Wont pass emissions without it

thank you for your brilliant idea! I got mine installed according to what I received. Bought it from Amazon for less then $50 and it worked great!

Did you have to remove the bumper to install?

buying one in a week for $2000 with only 120K milage

Hey Man i have a 91 integra i have the battery ligth on i change the alternator still the same i change the baterry the same if i remove the cables the car shut off what you think it is ?

My 94 GSR's twin.

What’s number 17 ?

Was that auto or 5 speed??

Looked nice with the black plastidip

by chance do you know where i get every since one of those o rings and gaskets for a full idle rehaul on my jdm b16a?

Hello, good video. Is there any benefit to ABS Delete?

You wouldn’t still have the cat and want to sell it?

Looks good bro! Great guide, thinking about doing this on my channel soon!

Nice one👍

Thank you. This video saved me from ripping my trans apart again to replace the plastic crap gear

Great video and you answered so many of my questions like the vibration especially if you're keeping the rest of the mounts stock and options for stiffness levels. I like that Hasport provides bolts that fill the hole in the middle of the mount, looks like I'll have to go with Hasport I wonder how much they are these days?

Telling what size tool or socket it took to loosen or remove needed bolts/nuts will get you fans sir

Man I'm not sure if you'll read this but your videos are super helpful. I honestly wish youd post some more. Especially on the teggy cause we literally have the same car down to even the wheels!

Ohhhhh so the two in the middle is your high beam thanks man

Do you still have integra i have cash in hand

Nice vid. I recently installed mine and I noticed it be shaking my steering wheel a lot . Did this happen to u? Any tips on how to reduce the steering wheel rattle/ wobble.? Ty.

What website did you order the Enkei RPF1 center cap from? I need some for my 16x8 rpf1

For the passenger side torque mount. You can easily remove the transmission to torque mount bracket. There’s 3 bolts. Then everything slips off easily.

Are those 16*7 rota slipstreams. I currently run 205 45 16 Wondering how wide i Can go

Thanks, it'll help for our 2018

What Finnish paint?

I have a 2006 limited I want to change the subi badges is that possible for those years

Toking .toking and nothing