Video

"avoids the oxygen sensor to pick up incorrect codes"... Lol. These are generally used to hide a bad catalytic converter (code p0420) from emissions testing. It literally pulles the 02 sensor out of the stream so it barely detects any gasses. If an emissions tester sees this, he will fail you. If you live in a non emissions testing state, the world is your oyster.

word of advice anytime u disconnect anything electrical always disconnect your battery first

Excellent tutorial!Thank you for your excellent detailed video Worked perfectly for my 2005 Honda Accord with 190.000 on her.

Thank you 🙏🏻

Thank you for the detail. This job took me thirty minutes.

Drive only works on the quick other cycle.It'll only run like five minutes And stop

Wooh thank you

🚨 Just make sure you are extremely careful when putting the bottom starter bolt back in.my threads were cross threaded when trying to put it back in 🚨

Honda fix this problem in 2006+. Now access to this sensor is more difficult, covered with extra plastic under collector, don't think about reaching it with your fingers.

Thanks, best video. Like in holywwod. where did you place a light ? You forgot to mention that need skilled hands to addition to all toools.-) My push tab located on 3 o'clock. Could not do it from take 1. You're lucky yours on 12, probably easier.

why the model have to be naked ? it will be more appropriate with only the wanted area exposed

Thanks, I managed to get a bit of practice removing a couple off parts cars at the wrecking lot. Afterwards, I did it to my car, had a bit of a hard time getting the sensor in, but I actually managed to secure the wire back on using my hands since I have skinny fingers haha. Hopefully the used one from the wrecker lasts! Thanks saved me a bunch of money at the mechanic.

Perfect video man thank u

Thanks Great demo video step by step

Mine's been playing up for about 3 weeks, smart diagnosis kept reporting no errors. I just checked the door and although I can't see light inside the drum, I did notice some movement. So I ran a diagnosis again and it's saying the door's not closed properly....are you a telepathic Dryer Whisperer? 😂 Hopefully hear from customer service early next week but at least now I can point them in some direction. 👍

Can you tell me where they sell the sensor spacer?

Well done. Thanks for the tips too.

Just fyi, Honda's are designed to be worked on from underneath.

Knock sensor 2004 Honda pilot

Hi where do you get the bushings and want size/product # would it be.

Thanks for your sharing❤

Sir please my question is, what causes someone to stammer, and what is the cure?

I imagine who created this heart, now I can understand how my heart works, I will mind what I take in, especially to the lungs. But I would like you to make a video explaining how a bad smelling environment can affect the heart... if it does affect it. Thank you sir for taking your time to make this video, I will always keep in touch with your channel to learn more about how my body functions 🙏

If you have a code? Put in a new sensor! WTF?

After 400,000 K you changed it?

Does anyone know the severity of this issue. I scanned my car and it said to change the sensor as soon as possible if I had driving issues. That it could damage the main system.

How do you know if you need the one with oil charge or regular R-134a?

Thank you for the information.

You are smart, man. Very helpful. Thank you!!! 🙌🏻

video starts @2:05

Mine is brand new - just tried to use it for the first time. The battery is fully charged but the mower turned over once and then stopped and won't restart. I wish I hadn't bought it. 😢

Video to show how to shampoo the inside of your car like a pro.

My 96 Camry calls for 32 ft lb. Tried to install a Beck/Arnley and the tip broke. (Pot metal made in China) Ordered an OEM, and hoping for better luck.

INTAKE MANIFOLD. ITS MADE OF METAL. HOSES ARENT MADE OF METAL.

The simplest explanation I have ever seen in internet.... thank you so much sir🙏

How often do u press it and for how long u press it for ??

Great video. Really helpful and well explained

Thank you

Two types..of sensor ..its single pin and twu pin..for instance two wires cut or eat the rat.. how to know to correct connection pin.

I was about to start on the repair but i have a 2006 and it has a platic piece below the intake manifold, making it impossible to see the knock sensor, looks like i have to remove the im.😢

did this work ? is it still working?

That thing looks like shit😂

So you had an engine code that you knock sensor was bad, but when you tested it, it showed that it was good, so your problem was not your knock sensor.

Tons of extra talking that just lengthens this video for no reason.

Thank you my friend. Another diy video on the accord. How is the recharge working so far? I have a 2004 accord

So you can reach in to plug the connector, but need a needle nose and a hose for the other steps?

The duct tape is hilarious. If anything, use masking or painters tape so your tools don't have sticky residue afterwards. Alternatively, you could use a stick magnet to retrieve the sensor if it falls out of the socket. When reinstalling (any threaded part), turn it counter-clockwise first until you hear/feel it *click*. Then, turn clockwise to tighten. There's only one 'entrance' on the threads of a machined screw/bolt. When you hear/feel the *click*, you've found it. Make sure the screw is straight, though!

Well done 👏🏽👏🏽👏🏽 thanks

I have changed this sensor, TWICE! the code comes and goes every few days. I thought the cat was bad, but I guess I will try this next.

I don't know what you call it, but it's the part where the latch is to the hood. The part you dangerously use as a shelf for your tools. .You can take off the nuts etc, and pop those couple of tac point. You can then lift and push back that back. it will give you about two inches more of room to get your arm in there and get it done easier. Otherwise, it's a bear.