![Quadrajet Power LLC](/img/default-banner.jpg)
- 29
- 520 702
Quadrajet Power LLC
United States
Registrace 6. 10. 2019
One stop Quadrajet shop. New and used parts, kits, and expert services.
www.quadrajetpower.com
www.quadrajetpower.com
Quadrajet Power how to replace power piston retainer
Steph describes how to remove the old shrunken power piston retainer and install our new retainer
SKU PPR
www.quadrajetpower.com
quadrajetpower.com/power-piston-retainer-new/
SKU PPR
www.quadrajetpower.com
quadrajetpower.com/power-piston-retainer-new/
zhlédnutí: 481
Video
Quadrajet Power - Early float pin damage repair
zhlédnutí 449Před 3 měsíci
Many quadrajets from 1965-1974 and almost all marine use carbs use the big float and have the vertical towers sticking up to hold the float pin. These easily break and the float won't stay in place. We sell the repair piece for this at www.quadrajetpower.com SKU is 139 quadrajetpower.com/float-pin-repair-bracket-new/
Quadrajet Power - How to install Hot Air or electric choke housing to the body
zhlédnutí 7KPřed 11 měsíci
Quadrajet Power provides details of how the hot air or electric choke housing mounts to the side of the Quadrajet. This video shows where the secondary lock out goes as well as the fast idle cam and other components. You can get all of your quadrajet parts, kits and supplies from us at www.quadrajetpower.com Items mentioned in this video New choke coil: quadrajetpower.com/hot-air-choke-coil-new...
Quadrajet Power how to 1965-1966 secondary system
zhlédnutí 1KPřed rokem
We explain the 1965 - 1966 Quadrajet secondary dampener system and how to install the pieces for that system.
Quadrajet Power early style press in needle/seat with O-ring
zhlédnutí 1,1KPřed rokem
We explain how to install the early style press in needle/seat with retainer for the 1965-1967 Quadrajet. www.quadrajetpower.com quadrajetpower.com/early-style-needle-and-seat-with-o-rings/
Quadrajet Power power piston clip install how to
zhlédnutí 2,4KPřed rokem
This video shows how to install the power piston retainer metal clip on the early 1965, 1966 and some 1967 Quadrajets www.quadrajetpower.com quadrajetpower.com/power-piston-retainer-clip-new/
Quadrajet Power main air bleed install
zhlédnutí 3,8KPřed 2 lety
All Quadrajets have main air bleeds. These may need to be sized or replaced to correctly calibrate the quadrajet for the engine it is being installed on. We can help you determine proper sizes and supply all the parts you need. www.quadrajetpower.com Main air bleeds. quadrajetpower.com/bleed-restrictions-pair-new/ Pick tool quadrajetpower.com/pick-tool-double-end/ Recalibration kit. quadrajetpo...
Quadrajet Power install primary rod retainer spring
zhlédnutí 2,9KPřed 2 lety
Installing primary rod retainer spring on power piston. Early type and later styles. Retainer spring holds primary rod against the jet to hold stead and not disrupt the fuel flow. www.quadrajetpower.com Early style. quadrajetpower.com/primary-rod-retainer-spring-early-style-new/ Later style. quadrajetpower.com/primary-rod-retainer-spring-later-style-new/ Power piston retainer. quadrajetpower.co...
Quadrajet Power How to attach your choke rod when it has disconnected.
zhlédnutí 14KPřed 2 lety
This video shows how you can re-attach your choke rod if it has become disconnected from the actuator on your Quadrajet. Without removing the air horn. www.quadrajetpower.com
Quadrajet Power Tuning part throttle with jet and rod combinations
zhlédnutí 12KPřed 2 lety
This video explains how to adjust your quadrajet part throttle fuel mixture rich and lean with different jet and primary rod combinations. Provides a brief description of the power piston stops at the APT screw. Also describes different primary rod types for APT in base, and internal APT screw. B series rods compared to K series and M series. www.quadrajetpower.com Parts available at www.quadra...
Quadrajet Power How to replace Quadrajet secondary rods
zhlédnutí 2,9KPřed 2 lety
Quick video to describe secondary rod function and how to quickly change them on the quadrajet. Qjet www.quadrajetpower.com New secondary rods DA quadrajetpower.com/da-secondary-rods-pair-new-440-tip/ AX quadrajetpower.com/ax-secondary-rods-pair-new-397-tip/ Used rods and hangers: quadrajetpower.com/hangers-secondary-rods/
Quadrajet Power How to change jets and primary rods in Quadrajet Qjet
zhlédnutí 9KPřed 2 lety
Detailed explanation on how to change jets and primary rods in the Quadrajet carburetor. Jets are located inside the fuel bowl and changing them requires you to remove the air horn and internal components. All parts, kits, and much more for the quadrajet are available at our website: www.quadrajetpower.com New Jets: quadrajetpower.com/jets/ New primary rods: quadrajetpower.com/primary-rods/ Use...
Quadrajet Power how to change quadrajet fuel filter
zhlédnutí 8KPřed 2 lety
How to change the Quadrajet fuel filter. 1965 to 1971 early style gasket 1972 to 1989 late style nylon gasket Marine screen filters with early gasket All parts available at www.quadrajetpower.com Please subscribe to our channel! 1966 to 1971 long filter kit: quadrajetpower.com/fuel-filter-kit-long-filter-early-inlet-gasket-spring/ 1972 to 1989 long filter kit: quadrajetpower.com/fuel-filter-kit...
Quadrajet Power Pulling idle tubes and sizing for proper idle. Down Channel Restrictions
zhlédnutí 9KPřed 2 lety
This video describes how to pull the quadrajet idle tubes and down channel restrictions. Cleaning and sizing the idle tube is critical for proper idle with any stock or modified engine. Engines with bigger cams or higher compression require more fuel through the idle circuit for engine to idle correctly with a quadrajet. This is how you make that modification. We have these items and hundreds m...
Quadrajet Power Setting fast idle speed and curb idle speed
zhlédnutí 62KPřed 2 lety
We show the process to adjust fast idle speed with choke active on the quadrajet and how to set curb idle speed when choke is fully open. www.quadrajetpower.com
Quadrajer Power Electric choke conversion for hot air choke Quadrajet
zhlédnutí 22KPřed 2 lety
Quadrajer Power Electric choke conversion for hot air choke Quadrajet
Quadrajet Power - Quadrajet idle circuits explained
zhlédnutí 29KPřed 3 lety
Quadrajet Power - Quadrajet idle circuits explained
Quadrajet Power - APT system description and adjustment
zhlédnutí 39KPřed 3 lety
Quadrajet Power - APT system description and adjustment
Quadrajet Power - Assembly of the Quadrajet
zhlédnutí 30KPřed 3 lety
Quadrajet Power - Assembly of the Quadrajet
Quadrajet Power - Air Horn rebuild and assembly
zhlédnutí 5KPřed 3 lety
Quadrajet Power - Air Horn rebuild and assembly
Quadrajet Power - Base Plate rebuild and assembly
zhlédnutí 16KPřed 3 lety
Quadrajet Power - Base Plate rebuild and assembly
Quadrajet Power - Installing divorced choke on the Quadrajet
zhlédnutí 22KPřed 4 lety
Quadrajet Power - Installing divorced choke on the Quadrajet
Quadrajet Power - Complete Quadrajet disassembly
zhlédnutí 9KPřed 4 lety
Quadrajet Power - Complete Quadrajet disassembly
Quadrajet Power - Quadrajet Carburetor Disassembly & Reassembly: step by step process
zhlédnutí 151KPřed 4 lety
Quadrajet Power - Quadrajet Carburetor Disassembly & Reassembly: step by step process
Quadrajet Power - Quadrajet Identification
zhlédnutí 51KPřed 4 lety
Quadrajet Power - Quadrajet Identification
Quadrajet Power Video Series Introduction
zhlédnutí 5KPřed 4 lety
Quadrajet Power Video Series Introduction
Quadrajet Power - Carburetor Plating and Body Recolor
zhlédnutí 3,1KPřed 4 lety
Quadrajet Power - Carburetor Plating and Body Recolor
Hello I just put a new carburetor kit in my quadrajet and for some reason I lost vacuum on the tube that pulls vacuum for the timing? What if I used the wrong gasket on the top side would that cause it to happen? Thanks Sir
You possibly used the incorrect throttle body gasket, between base and body. Order your kit from us and we will get you taken care of. www.quadrajetpower.com
Good video but please eat your food before doing video 🤮
Tolerance for a warped quadrajet, I have semi straightened it out but still have a 1-2mm gap from the centre to the secondary side where the 2 big screws go into the body. Base plate is also flat. I was thinking about making a set of gaskets to replicate and give myself another half a mm of tolerance or so on top of my new gaskets? Thoughts from anyone who sees this
Buy yourself a pair of flush nip cutters from dorman, Titan or Klein and you'll love them for stuff like this
Great video! Love it, always wondered about this APT thing
Does the APT system also affect the idle mixture screws? Could it be that if my idle is too rich (AFR of 12) that I would also need to turn down the APT screw in order to get the Idle Mixture screws effective?
Well done.straight to the point with the carb on the bench. Din’t have to fight with camera and mirror’s to show where screws were located..
pre sure power vavle acc pump few the vcum items and hoses had cruse set up all them bells now rather just pull it cap off lot stock for now less vacum just go old 2barrel basic
1983 march april 1983 g30 cutway rv 5.7 350 was mouse house haveing fun fix it got it run pop off etc no pedal idle yep geting them kits parts plan just get e-pump added newer block fuel pump still waiting get primp 43gallons half full that old gas had air cover so mustly just norm wear able parts
The rod end is so short and the fit is a little loose so it does not stay on. Thirty tries later and it keeps falling off during this process. Bad design.
Outstanding video by an expert.
I tried emailing you guys the other day about a carb and did not get a response
Email us at info@quadrajetpower.com Thank you
Sent one just now about a 7043208 quadrajet. 👍🏻
I have an early 70s QuadraJet with the divorce choke... want to change intake manifold, but keep the same carburetor. Is there a way to do this?
You could go to a manual choke or no choke system.
Is there a later QuadraJet with an electric choke that's comparable? If so, what would be the part number?
Thanks for the information!!
awesome videos
Are the nails the secret to carburetor repair? I'm willing to learn.
😂
I bought some parts from you in the past thanks for keeping these old carbs alive
Very helpful Sir! The instructions that came with mine were pretty vague on how to set the choke 👍👍
Great info, i resolved my issue by restricting the idle bypass hole air my mild BBC. The bypass holes were too big for my application, causing the idle mixtures not to respond very well at idle.
Made rebuilding my carb easy! Thanks!
Great video and I was wondering where you might know a site for an 1987 4 bl electric choke housing because my 3 housing screws were so tight they broke the crew hole casings off getting them loose?
ok.... what if i don't have an apt at that location?
Thanks for the info!!
The electric choke elament needs to be powered thru oil pressure switch.
I'm not sure what kit I need. I think it already has eletric chock but the choke flap stays open so I'm thinking replace everything.
What jetting, primary and secondary’s do I need for my 87 caprice classic quadrajet for here in TX? Was rebuilt and jetted for Colorado altitude so I need to change that. Any and all advice will be extremely appreciated
Great video!! I'm running a 350 with 2.02 , 1.60 valves and a bigger cam and have been having issues with idle. I'm pulling about 17 inches of vacuum at idle do you think I need bigger idle tubes? Or is this enough vacuum to make the stock ones work properly?
17 inches is about stock. A big cam will go down to 10 inches
Great instructional video... I really wish my father was alive to see how easy really is to do something we tried to do together but never really worked right.. again thank you..
How do yo cap tube from exhaust manifold that carried hot air to choke?
Good info! Thanks
Great videos. Can You explain fuel circuit, how it is controlled when on idle what is holding the fuel from part throttle and secondary fuel cuirciut from flooding the engine, can You explain what is triggering part throttle system to get in and same for secondaries. Air flaps and linkeages are visible but ilustration what is happening with fuel i think can be interesting and big step for understanding.
thank you that was what i needed for my 85 trans am to pass the emissions test in Colorado
thanks for the vid, my rod fell off too!
Have you worked on the secondaries accelerator system it helps take off. Some of the Qjets upper secondaries butterflies are slotted in front of the port to get higher vac signal sooner for more fuel. I normally drill them just shy of a wd40 straw anymore that that will be too rich.
Do these adjustments work the other way too? I had to adjust my choke thermostat clocking and vacuum pull off a while ago, and ever since then, my fast idle is really high and stays there for a very long time (5 mins or so before finally dropping down a bit). Is it possible that, by making these adjustments, I tightened up the fast idle cam?
Hi thank you for the great video. I see on your website I have to plug in my code on my quadrajet carburetor. I have a 17085213. Will the QB1 work for that?
good idea about position your camera in a different area so we can see what you're doing
I found a beautiful way to fix the Frozen and broken lower older apt that gets never adjusted because it's froze
cool!
With these carbs getting harder to find, this will save a piece that would have been scrapped years ago.
My only problem is doing a second gear WOT pull. The car sucks the bowl dry. Having to run a 3 nipple jeep fuel filter to prevent vapor lock. Would a 3 nipple hi volume mechanical fuel pump fix this???
These carbs were run from 230 CID Pontiac six cylinders to 454 Chevy big blocks. For such a range there were three different needle and seat assemblies for different fuel use ranges. You might check to see what you have vs what the carb came on. Max fuel pressure was rated at 7 psi.
You need good fuel volume to the carb. Use large needle/seat and check float height.
@@QuadrajetPowerLLC I'm using the modification kit you all sent me.
Would it help to remove that plastic cup. That would give me more fuel volume in the bowl. Correct???
Check your float height. Yes, you could remove the cup for more bowl volume. Check your entire fuel line, make sure no kinks or cracks.
Great idea. I'll be doing an early one in the next few months. Will be ordering everything from you.
So cool,thanks very nice!!
Great repair! Love these videos, keep em coming!
Genius!
I have a quadrajet rochester carburetor on my 327 small block chevy I ended up ordering a used carburetor off ebay and all numbers match. I watched Your video when I install this choke lever and and get it set up do I need to install a hose on passenger side of carburetor to operate the choke or how does that work
No hose needed for divorced choke carb. Choke element sits on intake and connects to carb with rod.
Between Ruggles book and your videos I am starting to understand how it works and how to fix my problem in the going off idle circuit. I have to richen up the idle circuit. My tubes are stuck pretty tight. I have to try to get them out again or try to drill them from the top and flush out any chips.
You have helped me to understand how to fix my problem. As soon as I go off idle with light throttle it falls on its face. I have had trouble getting out the tubes, even with heat. I am going to try again. If I just punch it and not on a hill it seems to bypass the intermediate circuit and go directly to the main circuit. It used to be extremely smooth until I put in another cam. If you have a flat tappet cam and have had failures go to diamond like coating (DLC) lifters and it all stops.
Can I swap the base from a electronic carb over to a non electronic so I can gain the use of the the TV cable mount? Without having a bunch of headaches?
It would be best to swap the primary shaft from one to the other.
I have a Camaro Z28 - 1984 - Trans. manual. T5 Question: When choosing a new and same Quadrajet 4BB carburetor, is it important to know if it is for a trans. auto. or manual??
That isn’t as important as starting with one that was originally designed for your engine.