Video

Someone in the comment section pointed out there’s a winch, and now I think I understand that the blue device on the floor to the right is what’s pulling the winch down. I was wondering why is there noise and why is the guy not using any muscle? I thought this was a trick done with a fork lift! You couldn’t pay me to go under that though!😂

It is very practical and simple, no system is infallible. ALWAYS HAVE 2 WAYS OF SAFETY! STAND UP AND PUT ON INDIVIDUAL SUPPORTS! muy práctico y sencillo , ningún sistema es infalible SIEMPRE TENER 2 FORMAS DE SEGURIDAD ¡¡ SE LEVANTA Y SE PONEN LOS APOYOS INDIVIDUALES ¡¡

the law of the lever...nice

Brilliant starting point but gusset/triangulate the joints in your fame for safety, and add pads or a fabricate pinch seam catch cradle on a pivot to protect the unibody rails from distortion and you've got an amazing, simple, and reliable inexpensive car lift solution. I wouldn't use the corner of a beam against either the pinch seams or the unibody rails.

Ideja je dobra ali realizacija nije. Tvoja dizalica će da grebe farbu sa auta. Bilo bi logično da je zaštitiš da bude mekana i da ne grebe farbu.

Add some casters to it and some pad mounts to be able to use difference clearance spaces for exhaust and what not and you have a solid DIY lift. Nice work boys!

Just have a fat girl stand on it for safety😂

Do that with a 3400 pound vehicle like normal people drive, then i might be impressed. The vehicle pictured looks smaller than a pinto. I bet the average physically fit man could lift the whole front of that car up without the lever.

отдельный гараж для этой хрени

pass

Scratchs the floor !!!

what would you like written on your tombstone..?

Just WOW 🤣

darwin's reward pretender...

Leverage is king & so are you for making this lift.

лонжероны продавлены , ободраны, отличный метод. А сзади, если торчат продольные рычаги, и лонжероны выше их. Задумка бред, подкатной домкрат удобнее и практичней.

👍

Having thought log & hard, I have just decided to do a massive facepalm........... bodgery at its best !!!!!!!! the damage to the car flatten the pinched seaams probably split them weaken the car, scrap off and protection what rubbish & potentially bloody dangerous

why go destroying cars bottom?

Wow finally i find this

What an economical innovation ❤️❤️❤️🎉💪

im making one asap. holyshit this is awsome

Put wheels on the point that’s touching the ground when it’s about to lift it will allow it to slide down flat on the ground much safer

Yep, with a big enough lever can lift anything, I was thinking on the lines of leverage for getting decent amount of height for when I want to work under my car. You could have tubes within tubes with holes and metal pegs for more length for greater leverage and more height from the part that provides the lift.

Ammiocuggino like this

Vu la hauteur du passage de roue à l'avant, je doute fort qu'il y ait un moteur dans cette voiture.

Пару роликов и строховочные рычаги

Bad idea

Cool

Когда твоя машина весит 800 кг, поднять еë не составляет особого труда

Oi

Hihi

Называется "пизда вашему днищу" 😂🤦‍♂️

Главное не придерживать и просто отпустить, и перевернётся как блин на сковородке.😂😂

So many things could go wrong in the wrong hands ...

👏👍

Adios exhaust system. 😅

o cara é um genio !!!

Dame una palanca y movere el mundo.👏💯

Хочешь угробить пол в гараже или автомобиль, сделай так, как болван.

Вот как нут пороги!!!!

That's your sills pinch welds destroyed lol

И пиздец твоим порогам!

Good for old cars

Gr8 job

If you could make this then make a ratch type with a shock absorber return then maybe easier to work from one side at a time use axle stands always

That is most likely Eurofighter Typhoon by the silluete and the intakes and also twin engine configuration .not Mirage

Poi succede qualcosa di irreparabile, come fate a mettere su i social tutto questo!!!😢

This is brilliant!! When it fails you don't have to worry about explaining how you ended up in a large scale mouse trap. This is definitely a good beta test, go back to the drawing board and continue engineering a better mechanism. You almost have it. 👍

I have a motorcycle lift that works the exact same way. It is the best lift I've ever used.