Video

I'm installing the upgraded shift plate and it comes with two black wires and no wiring diagram or even a simple explanation which wire is pos or neg. The old wires are a tan with a green stripe and a solid black. So there's no way to tell how to connect the new two black wires to the old tan/green and black. I was hoping you would cover that. It would've been very helpful if you had.

I have a 2005 Tahoe Q4 with a 4.3 seems to have this problem

What did you use to clean the module

You lost a subscribe and the election

Pressure is pressure. sucking or blowing will still indicate a leak.

Thanks

Very interesting, thanks

Thanks for posting. It fixed my problem! Not a cheap part, though!

This was an awesome video. Very clear. I have a OMC/VPSX with the cone shifter now, but I used to own an A1G2 with that dog clutch. Nice to see how all of that works, thanks to you. 👍

Super valuable video, thank you! I had the same issue and my mechanic just removed the switch..is that bad or can the engine live also without it? Also, I had an issue with the gears and neutral and the mechanic removed today the shift assist...since then the gears are working fine and smoothly, on land. Tomorrow we will test it on water. The engine is a 4.3LX V6 alpha one, carburetor engine. What are your thoughts on this? Thank you in advance.

Did u rebuild the carburetors or did u just clean them?

Nice cutting that open. I have a 77 Mercruiser R behind a 302 that ran low on oil. Smoked the very top bearing on the drive shaft so far that I can see. I’ll probably never take it apart like you said due to the cost of the tools.

Very cool demonstration, sorry your drive had to croak to show us.

I’m Please I 😅o o j

excellent video, thanks

Yep. Voting for Brandon!

Great explanation. About to change that on my 5.0

Thank for your instructional. It's really helpful!

Good video here. As for myself the first things I usually check is the fuel line, bulb, and check valve, then straight to the fuel pump(s)...an outboard that runs fine up to mid rpm then bogs is almost always being starved of fuel, and fuel pumps are so simple to inspect, and what I often find isnt a tear or hole but just a stretched out diaphragm that cant keep up at speed, that and the godawful tiny filters Mercury used to put pre-carb in the fuel lines that most people have no clue even exist.

Hi Mark, how would you change replace the tube line that goes to the speedometer?

You run the drill clockwise ?

CAN NOT FIX HIS OWN PROBLEMS 😇

He may need to sell the boat to pay his legal bills. Get ready for a call.

you convinced me Mark!

Are you really all so gullible....It's AI.

Man, this AI Trump shit is a rabbit hole I could lose my life in. So funny. I think I have TDS.

THIS IS A DEEP FAKE... it ain't Trump talking. --==== DEEP FAKE --- DEEP FAKE ====-- (it's pretty obvious)

❤ Cheers Mark!! 👍😎✊

Its so big and great it has its own golf course

Of course he will own the biggest best boat ever. He named it Titanic.

😂

You are so full of it

Hello, I have a question, when you install the reverse pinion, shall the dog clutch be in reverse position or in neutral ? Thanks in advance. Best regards.

Very helpful video. Now my boat is ready for the Biden boat parade. Just kidding, I'm not in a cult.

I don’t have the key FOB!

Yes and the splines where not reverse cut like the merc one of the problems, the other is the shift cable stretches a little and the gears jump by. Junk, merc and merc only

Thank you for the video

I've come to hate the TKS. I have had my carb rebuilt, and replaced this module. However my engine dies once the enrichment valve engages and closes off the enriched fuel/air. I troubleshot this motor for a whole summer and finally got it running good after replacing the spark plugs. Next summer, exact same problem again. Again new spark plugs, but no help.

Let’s go Brandon!

Where did ya get the replacement drive

Very useful, thank you!

Thank you, it worked great. Why the tire shop wont do this I don’t know

Great boat. Way ahead of its time. Love that model. True beast

What a great video and yes, I found it very helpful. Thanks for sharing. Cheers!

Supper❤❤❤

Never worked for my 13 Sierra

Thanks for this man! For those wondering, you only have to hold it for 10-15 secs and then wait for the horn before moving to the next tire.

thanks for the info!!

Super helpful, thank you!! I just got new tires for my gmc 2010 Sierra. The lights were on, and this solved it!!! Thank you!!

Hola , dónde compraste el reemplazo? Es para un motor V8? Un saludo