Video

What does this mean? thats the range you keep it at all the time ?

Nice ❤

Comment as-tu fait pour changer tes valeurs X et Y Qui sont à 10 000 ?

Por que reemplazo el panel de control

Una consulta por que reemplazo el panel de control?

Hello, what is filled in that gas tank Nitrogen?

Sound!!!!!!!!

Great it works, care to explain ports and pins ??

sound please

Sound?

very good machine thanks

Excellent!!!!!

How thick MDF can if cut?

good evening, can you help me with my problem? I get a drive lmc error, why does that happen?

hi cutter 12 mm wood if is possyble

I have a Rycus 50w can I change the laser source to a 100w or JPT?

Great job sir thanks for uploading ❤

Great job ❤

My ruida controller doesn't have the option of "manufactory settings". Is there something else it could be under?

Nasty...LOL

BEFORE YOU DO THIS: To those who don't have or know how to install the settings/parameters back after the reset, DON'T DO THIS. I had to find out the hard way. However, if you have an programming "bug" in the machine, like the axis motors not operating to speed all of the time, this fixed that issue for me. But now, I do not know how to set everything as it should be back at the right parameters to use my machine, its way out of whack now. If you can find a way to save the parameters to a USB before you reset and you know how to upload it back, be sure to do that first. I'm no computer genius, so I'm a little lost and searching for help at the moment.

This is co2 or fiber laser?

I think tuve is broken becouse show circle insteed of dot

Are these values are same for each machines?

It is very easy to mark colored metal. Much more difficult ist to mark pure metal in dark or bright. Please show us how this works

مااسم البرنامج اللذي تعمل عليه

Solved my issue, rewired the red dot and now working fine. Thank You for the video

Hi, on using "savetoufile" option we keep getting error -data handle failure. Any troubleshooting for this? (Windows 10)

thanks for your videos! I noticed that when I repeatedly cut the same design, the cut tends to gradually move a few millimeters down the Y axis and therefore the cut does not always reposition itself in the same point. What could be the problem? Thank you for your answer!

3:35 that is how to handle fiber optic laser cable. Bend it more!!! OMG

mere pass 100w lazer machine hai, marking nahi hora hai, maximum power se cut ho raha hai, 5 ka power speed 12 karo toh 5 mm acrylic bhi kat hora hai, iss ka solution kisi ko pata hai toh bataye

talk to me!

hello, i changed mine and having issues with confrigration, do you have a video on that

Have we need do y axis alignment after change belt?

I have the HL-1060S 80W, I asked for support a few years ago because my chuck rotary was not working, no one told me about this. The support person said it should be work just adjusting the settings in Lightburn (diameter and steps). Is it possible this work these days for my laser machine? or it does exist a different way to make it work?

Hello I have a problem with camfive laser machine can you help me

Hello, what about on Lightburn??

garbage video, missed all points.

Hi, Is the 1060 just as quiet when running as the 570? :)

Thank you for making this!!!

What is the white tape material that is used? I purchased one of these machines and it came with a roll of white tape, but upon inspection, it is a white backing for clear tape to mark measurements in in and mm for the bed, to Line up materials. I tried masking tape and paper, and they just burn and make a mess..

Can you send to me please the driver LMCV4 ?

Thank you!

What are the settings?

i have an omtech 100w co2 laser, would these settings work on mine as well since its a 100w also? thanks

Have tried mailing you guys through the website, but no answer :/