- 18
- 2 379
No Car Left Behind
United States
Registrace 17. 11. 2023
Video
Datsun Dragster Teardown Part two
zhlédnutí 339Před 2 měsíci
Getting it ready to finish the welding and get this thing done.
Bracket racing a 20 second turd.
zhlédnutí 120Před 2 měsíci
I'm still trying to get Freda the Fairmont dialed in. Not a good performance but always a good time.
Tuning Dual Webers, Mikunis, Dellortos, Solex SU Carbs.
zhlédnutí 396Před 2 měsíci
My quick method of tuning dual carb setups.
Summit series Pro bracket rounds.
zhlédnutí 27Před 3 měsíci
Getting the Go Pro ready for race season, I found a couple of rounds that got left behind.
Ported or Manifold vacuum?
zhlédnutí 98Před 3 měsíci
Just another opinion video about what to do with the vacuum can.
$215 chevy 454 tear down
zhlédnutí 137Před 3 měsíci
Really clean auction find 454. I got lucky on this one.
Flywheel resurface... sort of
zhlédnutí 122Před 3 měsíci
I finally got the flywheel machine to work. Now if I could just figure out how to turn on the camera.
No Mini Dozer Left Behind
zhlédnutí 42Před 3 měsíci
At the property after being sick. I needed some fresh air, and to get out of the shop.
Brackets and tabs... again.
zhlédnutí 57Před 4 měsíci
The never ending task of attaching components to the Datsun dragster.
Dragster engine run and channel intro (2.0)
zhlédnutí 39Před 5 měsíci
Dragster engine run and channel intro (2.0)
I hate to sound like a crusty old fart, but the modern parts-changers masquerading as mechanics could learn a lot from your channel. Keep it up, Eric!
Thank you, Sir! Thank you for the support.
Seems to me that I once saw a green Dodge Dart doing the same thing at SIR. Knocking out alot of cars out. He was just consistant. Fun to watch him leave slow. The other guy having to watch and then only to break out. I also remember doing a run at that same track in a old ford, Me and this guy that was riding along. While we staged and eating pizza. A blistering 74 MPH. Those were some good times, I miss them! Keep it up Britain. We all are with you!!
I have enough time in this car to eat a whole piece of pizza and make a sandwich. this car traps at a blistering 67mph. Thank you for the good times and the support.
Simple, straight forward. Thanks for making this video.
Thank you for supporting my Channel!
Awesome to watch a carb rebuild from start to finish! I would love to see more on how to tune the jets and everything for use.
Hi Austin! Thanks for watching. I'm hoping to do a tuning video soon. I appreciate the input.
you need tdc range in degrees .
Hi Null. Most timing markers have before and after 10 to 15 degrees. This just picks up where they leave off. Thank you for watching!
Great information!❤
468 CI time.
That’s what I’m thinking too!
What a find!!
Absolutely unbelievable how time can stop for these
I have a question? What is the difference between a bracket and a tab? nice work though. the shop has come a long way, equipment wise. agree with GullWinginnMoclips. Great job Eric!!!
Nice work, Eric! If I may be so bold, you might want to reduce the volume of the music or raise the volume of your dialog. They are far apart... at least on my pooter.
Thank you sir. I've been struggling with picture and sound since day one. Nothing I buy seems to work. I'm still using my cell phone. It will get better.
I am amazed with your welding skills! You must have had a good teacher. More power to you. Keep the videos rolling.
Ya who was that guy?
The videos alway amaze me!
Great video! What are you making there?
Hey Eric...good start. If you're looking for some critique, photos are solid. However, I suggest you keep the "Fonts" consistent throughout and allow a little more time to read each one. Also, it may help to bump them up off the bottom of the page a tad as it draws your attention away from the subject when trying to read them. My two cents worth.
Thank you for the feedback Buddy. I agree, lots of room for improvement.
Hey Eric! John Kelly here... nice ice stuff!
Hi John! Thanks for watching. Much appreciated.