Video

Thank you. After watching this video im going to give it a go.

Where did you buy the headlight at

This sure helps me out ! Now I know what I'm in for ! Thank you for your video !

Thanks for taking the time to make the video, i got an AVT Bull Bar for my 2020 Ram Laramie Black edition, the instructions really suck as do the photos and seems none of the bull bar suppliers take the time to show the whole process. Your video helped a great deal as the mountings for the RC and the AVT bull bar are pretty much the same. at 73 years old I know the air dam spoilers gonna be a pain and like you without a proper garage lift getting under the front is tough, but a lot less tough than for a youngster like you. Be interested to know if your AC system sucks, here in Florida its just pretty crap on these Rams this is my third and all have been the same

I broke that clip too, I was so frustrated with it I went to look for a video on how to remove without breaking it for when I do the other side tomorrow. Good to know it’s not a huge deal and goes back on tight. Edit: finished the install, turns out that broken clip was the least of my problems. Nearly every bolt to take the grill off gave me problems. One of them just snapped, another the clip came off so it was just spinning and wouldn’t loosen, the other side same bolt came mostly out then the clip came off and started spinning. Whoever was on the line for the front end that day didn’t give a shit. I managed it and it’s all back on tight enough with the remaining bolts but what a headache it was.

Great video and I believe that is an impact driver that you used with the T30.

Cabin air filter CRV 2016 0:30

Can the interior lights be changed or should I buy a complete light?

Thanks brother for the information

I have a 2016 Ram Rebel and I’ve been wanting to add a bull bar to my truck… but I can’t find a bull bar that fits the rebels anywhere….

YOUR BRAKES ARE NEW DONT TRUST THE STEELER DEALER.

Great vid bud

Those Torx bits will be a pain for anyone living where they salt. So much easier on the classic model.

nice

Bro chrome delete the truck ! It’ll dope

Don't compress .🧐Just the rear brakes ❓

Did I miss how you removed the rear rotor????

Your video was a big help for the rears thanks you

Great video very helpful. Even managed not to break those same clips.

Could you show where you used your jack stands on the front.

Awesome looking Ride!👍

Thanks 🙏🙏🙏

I took a worn out 86 and made a road course car out of it. The potential of the platform is amazing. An LS swap solves the lack of power in a C4.

Gorgeous car. Have fun. Be safe. I own a 92,and a 96 lt4. Both very enjoyable.

Lock washers go on the nut side not the bolt end. If you can’t do the whole job you probably shouldn’t be doing it at all. Secondly a bull bar on a Laramie is just ridiculous

brakes look good to me just sayin

Nope go get finger printed noah Patterson

It’s worth noting… When pressing the caliper pistons back in, you should crack open the bleeder screw so you’re not putting undue pressure in the brake lines. The step would also force out any air bubbles or inconsistencies in the fluid level. Great video and information on the Z 36 performance kit

You suck bro, you didn't even finish the install WTF ?

FYI that tab on the rear pad you were not sure had a purpose….thats the tab that lets you know when to change the pads and will make the squeel sound when your pads to low

To avoid the broken clips, the tire has to come off and the inner fender well then you can reach the clips to the front trim piece under the headlamp.

I’m at a loss for words

I have a 91 C4

congrats! great color combo

i had a tough first round draw, will you be back in December? I was in the black gt350, we will be back in December for sure!

I just unsubscribed.🤣 The skinny right pedal is the business one. Go hard and nice job!

13k

Even after putting the parking brake into service mode it will not retract, I don’t have c clamps to use right now as I cannot find them, and am waiting on a buddy to bring some by to borrow. I only have one side off right now, do you think that may be an issue?

Back in the 80s I was the NHRA Division 2 photographer, shot a lot of races there and did a lot of Dicks Winter Series races for him.

Very nice!

Dude!! This is probably the BEST "how to - I think" video i've ever watched. Not being a mechanic or handyman and showing your struggles along the was makes me feel so much better about attempting to do this myself. I was sure I was going to pay someone, and I might still end up there, but now I'm going to try to do it my self. Thank you so much for being real and explaining everything so well. you have a new fan and subscriber

NICE, Enjoy.....

Do you race?

Congratulations 🎊🎉

Fantastic C4!!! I'm restoring a '92, same beige interior but was originally white now going to a 2-tone red...dark (top half) and very dark (bottom half), with flat black moulding and gloss black roll bar. The Targa roof is blue or grey tinted Lexan. Look on CZcams for C4 mods, lots of great ideas that aren't too pricey. The modification to your throttle body is probably an "air foil" which smooths out the air flow through it. I bought one, then wound up buying a new TB. Have fun with your project, I'll be looking forward to seeing updates.

Dam, that is one clean C4, congrats

Awesome and congratulations..! I purchased a Black C4 95 in April 2021 with 87,000 miles for $9,500 in Abilene TX... it is factory except the battery and everything on it works...love the car... the reason the hood lights were unplugged is because the mercury switch in the hood lights will stick and sometimes they stay on after you shut the hood and they will run the battery down... mine were also unplugged

My 2019 rotors pulsated till I replaced front and rear pads and rotors

Just subscribed to your channel because you purchased the C4. I have had 3 C4's and I currently own a 94 Admiral Blue six speed. Love the car. Enjoyed the video. Congratulations on your purchase.

Hi Debbie and Danny. Awesome friend ❤️