Video

I hope you found it useful!! steve

Hi, We cover the current division factor in the course. Regards Steve

Hi, The 5P20 CT’s will be less accurate than the class X CT’s, this will become clear if you have a high current fault and the relays at the two ends will show different current levels, this difference may in incorrectly identify a fault on the line being protected. Regards Steve

@@Electricalsteve tq steve..👍

Welcome!

Thank you! 😃

Hi Tom, unfortunately that’s not an option on Udemy, you need to pay for each course separately. Regards Steve

Hi Kevin, at several cable joints along the route we ground the sheath with a non linear resistor to keep the induced voltage down to an acceptable level. steve

You're very welcome!

thanks!!

Hi Nino, I would suggest looking at the free CZcams videos to give you an introduction, if your interested do the full Udemy courses to give you in depth knowledge. Regards Steve

Always welcome

Thanks for the feedback!!

Hi Ryan, Use the voucher code TWHD1001 to get the following Udemy courses for $9.99…. ELECTRICAL CONTROL & PROTECTION SYSTEMS ELECTRICAL CONTROL & PROTECTION SYSTEMS PART 2 ELECTRICAL CONTROL & PROTECTION SYSTEMS PART 3 ELECTRICAL CONTROL & PROTECTION SYSTEMS PART 4 ELECTRICAL CONTROL & PROTECTION SYSTEMS PART 5 AIR INSULATED SUBSTATION DESIGN AIR INSULATED SUBSTATION DESIGN PART 2 AIR INSULATED SUBSTATION DESIGN PART 3 SUBSTATION GROUNDING ELECTRICAL POWER EQUIPMENT ELECTRICAL POWER ENGINEERING CONSTRUCTION SITE ELECTRICAL SYSTEM DESIGN COUPONS ONLY VALID UNTIL THE 3rd March 2024 Regards steve

Glad it was helpful!

Much appreciated!

Thanks a lot

pide ayuda a udemy

Hi, it’s not really an ANSI/IEC conflict, most utilities only have one set of current transformers on the line side now to save money and use other protection functions to detect a fault in between the CT / circuit breaker ( short stub fault ). Steve

@@Electricalsteve Maybe it's a regional thing. I commission HV substations, including the apparatus outside and the protection systems inside the control house. Our standard new dead tank circuit breakers have a total of 18 CT's per breaker. For a line breaker the bus side CT's are used for primary and secondary line protection and the line side CT's are for primary / secondary bus protection. Having the diff CT's on line side ensures the breaker itself is covered in the diff scheme. In a ring or breaker and a half scheme, it may be a little different. One last set of CT's may be used for breaker failure protection and the last may be for revenue metering. We have older installations that don't have as many CT's (we call CT deficient), but that can cause issues down the line - shared CT circuits and someone does maintenance test with doble -plugs paddle in while connected to doble and shorts diff relay and a nuisance trip. I believe for the relative low cost of additional CT's on a dead tank, many utilities choose to have the extra CT's for flexibility and ease of wiring and maintenance. Digital relays also help quite a bit if sharing CT's as the polarity can be adjusted internally in the relay for compensate.

thanks!!

Welcome!

Am glad you found them useful!!

Hi Muhammad , To use the attached coupon code go to the Udemy website, register, search for the course / my name ( Stephen Brooks ) then select the course you want and enter the $9.99 voucher code UHEK1001 Regards steve

Thank you for this. I was questioning myself on this video.

Hi, The system voltage is kept constant regardless of the power output of the transformers or the size of the loads. If the voltage is constant then the only thing that can change as the power magnitude changes is the current and it does, when the power drawn by the load increases the current increases. Regards Steve

Thanks for the kind words Kenneth, glad you found the course useful!! Steve

Thanks 🙂

Glad you liked it

Hi Zaid Go to the Udemy website, search for courses under my name ( Stephen brooks ) & use the voucher code IGST1001 to get them for $9.99, vouchers expire in 5 days. Regards Stephen Brooks

Hi, Every cable has its own unique bending radius defined by the manufacturer. steve

Hi Daniel Go to the Udemy website, search for courses under my name ( Stephen brooks ) & use the voucher code IGST1001 to get them for $9.99, vouchers expire in 5 days. Regards Stephen Brooks

@@Electricalsteve Thank you, purchased.

Hi Osman, I recommend 1.5 meters in the video, but the actual distance will depend on your circumstances….as a minimum you need to be able to walk between the opened panel door and wall…Steve