Video

Its a beast

Artea 1030

Can you provide online setup?

Hi

I bought one and can’t find a manual. Not quite sure why it doesn’t run. Can you sell me a manual

How much is cost of this machine?

Wonder how it does with 3mm going on 1.125 particle board work tops with radius edges? Some of the tops I do are 72" long, 36" wide with a full radius end.

Ahhh! only open one side if the UDF makes sense.. i did both sides a while back and was too much flow..i use MDF now, and i use some cheap masking tape to make a seal around the peice im cutting to create good hold..ill have to try the UDF nxt time again and only open one side..

hello, new to cnc. I am having a slight issue. Carving kitchen furniture doors, all good , but when it comes to cut a bit the mdf edges, like half a centimeter each side, it moves the material on the last pass. It passes twice, first time at 8 mm depth and 2nd time at 9mm depth, at a speed of 2000 mm / min. On the second pass, right when its doing the corners, moves a bit the board, on each corner, and bye bye the project. My question is, does it matter A LOT , the state of the board that is under ? because i am having trouble cutting at a depth that is correct to avoid damaging the board that is under. Closest i got was 1 mm depth when i cut the mdf. I fear that if i rise the depth it cuts by even 0.5 mm, it won't cut the mdf correctly and i will have to polish it after, Might as well end up doing it, if its so important that the mdf/udf support stays as clean as it can, no cuts on it. Also thinking to put 3 passes , like 6-6-4.5 mm ? at a lower speed, 1000-1500 mm/min ??

is these are working condition

Can you imagine getting a teenager interested in this now a days. We will have to wait a couple generations. Old guy signing off

Very impressive!

What is the name of the vacuum meter you used?

Is there another name for LDF? I'm having a hard time finding any info about this.

best video I have seen today

Great video

wow Top machine I am designer CNC

The best machines in the industry.

😊👍

Very educating . Helpful in every aspect .

This was really great.

Very informative!

you are great!, nice efficient

nice work

i liked your video.

nice job man

Very cool.

WHAT WAS THE REASON FOR SURFACING THE LDF ONE SIDE AND NOT 2 SIDES?

www.youtube.com/@mustaqeemkhan3440

Good stuff!!

Where could I buy that sanding attachment

𝐩𝐫𝐨𝐦𝐨𝐬𝐦 🤣

What's the full description of the machine and price please 🙏

Price please

Price ?

Hello, this machine is available in india if yes then price

Can it do compound miters. I need it to do 15 degree miter and 3 degree compound.

Hanzhen harmonic drive gear , strain wave reducer, robot joint , over 30 years experience

Hey, this is a great video! i have a few questions about the different types of board to use. To further ask about these types of boards i wanted to tell you why i am asking. I am asking because i run a 20 foot AXYZ CNC table. I am about to install 1” MDF board. The main reason is because we have to plane the table often because of how often we cut into our board. I cut ACM for a commercial size business. Just as i said we cut into the board often and that’s not the reason why i’m asking the question. i’m asking the question because we have had suction problems in the past. With the example you just showed me is very helpful, but i need to know about MDF board and how useful is it in my situation. Okay, that was a lot to understand. if you’re catching what i am saying that great. So for a question that i am asking is if i have a 1”MDF board and I plane both sides then install it. Which is what i’m planning on doing. Would you think everything so far is correct. If so that’s what i’m doing and the next step is to put on the material, then i would do a pressure test. And if i ran the who table which is 20’. I only use 16’ of the table at a time. So would you recommend adding on a 4’ piece to make sure the table is complete and has full suction. I’m asking because the test shows that’s now always the case. So please reach out to me at 435 666 0942 or christianscott8989@gmail.com I would be very happy to have a conversation on all of this! Thank you very much and please respond as soon as possible!

Where can I find this sanding attachment? The link in your comments is broken.

Do you sell this sanding head ?

Great advice. Thank you, especially with maintaining our files and rasps! On to watch your paste wax video....

One of the most helpful vids I’ve seen in a long time. Thanks.

I’m here for my wood working class and I think you did a great job

Awesome video, thanks.

I’m here for my wood working class and I think you did a great job 😍😄😄

This video has helped me a lot as I have serious rust problems in my garage

So nice

Circle T Easy Coping Machine C220 national machine is very necessary for my organization. *__*

Such a modern machine greatly increases the speed of work.