Video

Thank you.

Merhaba. Zaten bu video yapmak istediğiniz açıklamakta. Eğer video anlaşılmadı ise destek almalısınız. DNC aktarım cihazi ile daha önce denemedim.

You're welcome.

@@yclkorkmaz where are you men??? Iam in iran my job is cnc repair how can i learn fanuc parameters????

I am here. Follow my videos..

Amin, sizin de.

You're welcome

Henüz yok. Ileride Türkçe yayaınlayacağım. Şimdilik alt yazı seçip izleyebilirsiniz.

Hi, Sorry. I don't understand what you want to learn exactly.

If you be sure do everything right as step by step and the axis can move by MPG, try all axis to home position by MPG, then turn-off and turm-on machine and try again.

@@yclkorkmaz I will give that a try, thank you.

You're welcome.

Videoda tuşların yeri belli. Buna göre hareket edebilirsin. Bunun dışında, ayrıca makina kitabında hangi tuşlar olduğunu da gösteriyor. Bu işlemi anlatıyor.

Yes, there must be INPUT button on the Fanuc buttons. If the button doesn't work, may be its defective or may be you can not use it.

@@yclkorkmaz only have input button. There is no +input button.

The INPUT button is enough. Already no +INPUT button on Fanuc buttons.

@@yclkorkmaz having +input button help me not to use calculator when i add the value.

+INPUT button use on generally i guess from begining " i " series like Oi-MB, MC, 18i and etc. Probably no possible use it on O-M and O-T series. You must calculate the value then INPUT to your cnc.

Teşekkürler..

Merhabalar. Teşekkür ederim takip için. Ex ile başlayan alarmlar ( External ) 'dan yani dışsal cnc ile ilgili, Fanuc ile ilgili olmayan alarmlardır ve her makina üreticisinde alarm kodu alarma göre değişir. Bu alarmların ne olduğu ve çözümü, makina ile beraber gelen kitapçıklarda vardır. Yok ise, makina alarm verdiğinde bana alarm ne olduğunu gösteren ekran fotosunu gönderiniz. Yardımcı olamaya çalışayım. E-postam: yclkorkmaz@yahoo.com

Yucel bey mail adresinize gönderdim ilgli arızaya ait fotoyu. ​@@yclkorkmaz

Hi, i may try help you. What is the problem on the machine?

@@yclkorkmaz z axes over travel but it have not reached the limit yet. I tried changing the parameters but it didn’t work.

Probably your machine has two switches. One of them for home, another one for EMG stop. If, when you send z axis home and the machines gives Z Axis over travel alarm, the machine probably lost its home pos. For solution, especialy focus below show the video's after 12th minute. It shows a quick solution. If still the problem going on, follow more belowest show the videos links. czcams.com/video/wUWDaZc466s/video.htmlsi=Xuk1urXUUaQPUETf After try CAN+P buttons same time push and wait solution like shows in upper video, check below show the videos. czcams.com/video/6-gzZVnt0Xc/video.htmlsi=Aixh5g9IBaRki2uf czcams.com/video/dcdIQCTSpR8/video.htmlsi=ft_WLj0Z6UVoJIlQ

Rica ederim

Rica ederim

Yes. Try find your request in below shows the videos those from CZcams.

czcams.com/video/rrRDTa6R7E0/video.htmlsi=YQ4m5ITNgIXb5hYU

czcams.com/video/dEIMeZOH7hk/video.htmlsi=vKWZCkLMIzPAQUCu

@@yclkorkmaz Thank you, i have seen these videos, however I can not see how to transfer PARAM from CNC to pc.

Your machine's control unit kind of old right? Like O-T or O-M right? If yes, i don't have yet PARAM back-up for kind of these unit. I'will try load video for these unit about how to make back-up. Keep in touch.

czcams.com/video/HOnAJH352nk/video.htmlsi=eDZWO9_YhN8S3t-R

czcams.com/video/0g7TE67CU-g/video.htmlsi=RPPo3GYMBIT-7cZF

Bu yukarıda verdiğim CZcams video linklerine bak. Yardımcı olacaktır sana.

@@yclkorkmaz Elinize sağlık hocam çok sağ olun teşekkür ederim..

@@yclkorkmaz Elinize sağlık hocam çok sağ olun teşekkür ederim..

Okay. I am happy for you. Good luck .

You're welcome!

You're welcome.

You're welcome.

You're welcome.

This alarm special future for Nicolas Correa. It is mean, if this machine is horizontal boring machine, the Y axis Hydraulic Ballance has a problem. For the clear understand what is it 03 alarm, check this machine's Trouble Shooting Manual. May bei the hydraulic oil is not enough. May be the pressure of oil tank is not enough. Etc..

😊

You're welcome. Safety First!

@@yclkorkmaz I was wondering if you might know any more about this servo driver A06B-6079-H014 I was careful and replaced the cooling fan with a new one purchased according to the correct part number. That is all right. After I installed the servo driver and turned the machine on it was still giving the error 414 and the code number 1 on the unit itself. The new fan is also not working. There is a very slight electrical burn smell after I turned the machine on. That was very small though. I tested the voltages, 5v. 24 volts and 240 volts. There is voltage as there should be. The Fanuc book says if there are voltages as there should be then the unit is defective. That is about a + of $2000 replacement of the whole unit. I put a tester on the two bars which go between the power supply and the servo driver. There is no register there. Perhaps there is not supposed to be anything there. Any thoughts? Thanks, Bob

@@yclkorkmaz I forgot to mention that the 414 alarm on my machine is not for the X and Z axis. I do not have a Y axis. The error message reads 414 Servo Alarm 6 Axis detect Err The servo drive on my Hardinge T-42 Conquest has live tooling and C spindle axis. I thought that perhaps it might be of the spindle axis that the Driver is for.

If your machine gives " 414 Servo Alarm 6 Axis detect Err ", probably you have multi axis ( 6 axis ) swiss type lathe. If yes, may be the machine's Fanuc Power Supply Module ( PSM ) has defective. That's why you can not see any DC voltage on the DC bars. If i am not wrong, normally, the PSM module sends DC voltage to spindle and other axis drivers. If AC voltage coming to the PSM, but no exit DC voltage from PSM, as i wrote, the PSM has problem may be. You don't need exactly buy new module. You may choice repair it from your local private service companies.

Zamanla Türkçe videolar daha da artacak.

You're welcome. I will broadcast in timely more..

Thank you.

I checked on internet the program that i use before. I found this webside. " www.serv-u.com/ "

Your choice. CNC EDIT i reccomend.

@@yclkorkmaz thank u so much sir. And I salute to you. For your hard work . provide knowledgable video thank u again .sir. I please make a video of data transfer pc to cnc and vice versa and how to make backup of parameters..many more eople are facing these type of problem..so I humbly request to you make details video .thank u so much ..

You're welcome. You may find the videos in this my CZcams channel about those request like Cnc-PC data transfer via RS-232. I am sending a links from some of them here. It is; czcams.com/video/rrRDTa6R7E0/video.htmlsi=4IKBjDFJCYXXKIyH czcams.com/video/dEIMeZOH7hk/video.htmlsi=bs0BG0l-lsc4jugx

Thank you.

Teşekkür ederim. Zamanla Türkçe videolari arttiracağim.

Zamanla hazırlayacağım..

Thank you. Low voltage of the control power supply is one of the causes of this error. Check the power line cables with prefessional electrician.

Thank you..

Probably there is Tool Reseting M code on your machine. Try find the code from the machine's manuals.

Machine was done..fanuc oi md go to system, pmcmtn, data D444,D445,D451 is it tool magazine tool reset. End the finally M76 ( count 1) cycle start.

Ok. Good.

I did not yet take video for it. If i do, i will broadcast in CZcams.

You're welcome

You're welcome..

Thank you

Good

Thank you. Good for you. Something manufacture it good.

@@yclkorkmaz I want to learn more sir how to approach in fanuc system like custom screen making for the operator easy handling and more things

Its answer is from your local Fanuc Supplier. Not me. Contact with them.

@@yclkorkmaz there's no supplier itz directly from fanuc

Sorry for that. I can not do anything about it.

Hi. Thank you. I am from Turkiye. You may keep follow me.

Şimdilik türkçe çeviri hazır değil. Ancak ayarlar, alt yazı, otomatik çevir bölümünden Türkçe seçip izeleyebilirsin. Eğer 2 makina aynı anda bu alarma düşüyorsa, atelye elektriği 2 faza düşmüş olabilir. Ya da bu iki makina duvarda bi sigortadan besleniyor ise, sigorta bi fazı geçirmemiş olabilir. Ya da bu iki makina bi regülatörden besleniyor ise regülatör bi fazı geçirmemiştir.

Thank you..

​@@yclkorkmazwelcome brother 😊

Thank you