Video

I hope u know u have the chrono set at 2.0 grams not .2 grams...that's why u have 9 jouls 😂

Hi , i see a piece with some blue on it , is a part that needs a rubber and you forgot to tell about ? Ty

My scorpion is shooting full auto even without a trigger in it is my board fried? Used a bigger lipo 11.1v battery normally used for RC.

Where did you get the green blowback nozzle

Have you a video showing the tricks to removing the V2 box? Have you chopped a V2 Nuprol gearbox to suit an ETU to replace the microswitch?

Keep it up always a pleasure cheers ever in Canada reach out we'll going to a top notch outdoor club that's all forest with buildings and trenches.

Great video 😎 What would you recommend for a HPA DMR build? I've s-hopped my AEG but I want to install a kythera into it now

I drilled a hole in the top of the trigger, angled to the back. Put a screw in there so I could actually adjust the sensitivity.

PERFECT! I get this thing tomorrow and will need to swap the barrel, thanks a ton for this

I have one also, take the front plastic plate of the drive cog/gearbox (3 screws) and check both grub screws are in and tight. One feel out on me and the other was loose causing movement of gearbox and gear slippage. This will strip the teeth eventually

Very detailed. Thank you!

God bless you, needed this video so much

I have an evo: what barrel with cnc hopup you use? I have the SMG variant.

What nozzle size are you using or are you just using a stock jack nozzle

Please explain how you made the holes perfect in the middle. im pulling my hair out, trying to make them perfect like you did?

The empty mag detector is working for you??

Thank you very much, this was the vid I needed!

Hey, what size screw is it?

By far the most descriptive video for the hammer assembly. Thank you for the help with actually showing how things are supposed to go. Awesome vid thanks again

I know this is two years later but I just tried this hack and it still works

Thank you ❤

I did the ER HOP with my custom Dmr barrel using just a vice and some metal hand files (with some precision files for deburring) and its not that scary if you're willing to spend half an hour carefully filing...I did it as I wanted to use the 7mm CNC nub in my max hop unit...not only is it working brilliantly...it also flies out to about 90meter at 450fps(368 using 0.3bbs)...I'm an engineer by trade and a tech all my own guns..but it is doable and it does have amazing results...

What kind of grease do you use?

what screw is used

Hi mate I have just bought a scorpion Evo HPA in your opinion what is the best hop up to put in , I find that the stock hop has not got enough fine adjustment any advice would be much appreciated thanks 👍

Thanks for the information

four hours is taking me so fucking far...

Thanks for the video. It explained a lot. It's exactly what I needed.

Have instagram?

What would be a better motor upgrade high torque high speed or stock?

What kind of screw size is it

IS THE V2 M4/M16 ????

Do you have a build guide for your aap?

U filed valve knocker? Because if u put a shrink tube on there without it will lower fps a lot

Thanks Bro !!! Very help me !!!

Thanks a bunch... I couldn't find a screw but what I ended up using was an alen wrench. Metric was loose and wobbled a bit so changed to standard and cut a bit shorter. Fit fairly snug and works like a charm. Just cut it down with a cutting wheel on an angle grinder. Dremel tool would work too, whatever is handy. Thanks again 🤙.

i just bought the cowcow steel hammer set. But its kinda overpriced ngl

You made the hpa convertión or is the stock one??

Nice video! Can you show me the flight path of the bb with the different types of hop?

I really wish someone could explain how adjust the hop unit properly. I cannot for the life of me get it right and I can't find anything other than walls of texts trying to explain but ending up telling me to just wing it. I went from 0.9j to 0.2j And I can't get the power back up.

I went from 0.9j to 0.2j and I can't find ANYTHING on how to actually adjust it properly. This is not a product I would recommend

This is a sweet airsoft gun I have the Tokyo Marui HK45 Tactical in FDE just got it recently so soon as I get some green gas I can take some shots

Thanks, i just got mine PKM this week 🔥🔥🔥

Lets say I wanna shorten my LCK 74M to something like this would I be able to by just switching out the outer Barrel and inner barrel along with the furniture?

Hi Webby, I tried doing this on my SSX23 but now it doesn’t seem to be releasing much gas. If I manually push the hammer forwards I get a nice jet. Any ideas on troubleshooting? Thanks!

also seems like keeping tension on the spring would be bad no?

seems like i can only fit my screw to the right directly underneath the spring, and it moves every time i pull the trigger

Hey i got the same hop-up what bucking should i be runing? i have a 60 degree maple

Whats the best way to cut the hole in the middle of the scotch brite? The ones you made looks perfects

Hi, im finding these videos very useful thank you, i do have a question, how do you lock the evo to semi only please