Video

If you can get your hands on any, put a convex washer under the nut before you weld it

I got a 1999 Toyota forerunner and I just want the rear window rolled up but I want to do it manually without power. Any tips? You seem like you know quite a bit.

I got an old unloved 1st gen 4 runner, Mine needs work, but man I don’t envy you. That one had the mad wire hacker in there. I am at point in vid where you just started messing with the rear. Can’t wait til you bring it back to glory days.. Good luck

What ever happened to the Takeuchi Excavator, did you ever get it to run? No part two???

#dewaltsucks

Which throttle body did you buy on rock auto if you remember?

Yeah your bottom head....😮😂😂😂

My old auto teacher used to say “everything understands a little bit of force, women, children, and cars” 😂

These don't come compressed. Just remove the one arm bolt and lime it up, than use a jack to jack up the arm and align that bolt again and put everything back together. 👌 Please dont do this my friends. Used a jack and take that back bolt off

What conversion kit did you use? I have a 1999 F350, and the parking brake is shot.

Don't they come compressed with zip ties on them? And then you're supposed to install them with the zip ties on them and then once they're installed you cut the zip ties off that's how I do it works every time there's no headache I'm just wondering if yours didn't come with zip ties already compressed

what did you do about the Tcase and utilze the toyota axle being a passanger side drop pumkin?

Im currently looking at an ls swap along with the 3 link sas swap. my question is the ls stock oil pan is a clearance issue for my build. im wanting to wheel it. and curious to know if i got a low profile ls oil pan if it would give me more room for axle up travel.

Just a simple jack to take pressure off the body of the bolt, make life a lot more easy

Kinda looks like an f150. If you ever run into that again put your impact on the bolt and spin it with out putting force towards the bolt. They will probably twist them selves out. You can put an open end wrench that's smaller than the bolt head but larger than the shank and pull when spinning.

The hammer looks like a steal bottle

Thats alot of plastic...

Nice facelift

Real nice truck

Oh hell no it's not to late to throw that crap back in the box and go to the junkyard and get all the disc brake parts from a later truck. That kit doesn't have a disc brake master cylinder or prop valve, also an off road kit is code word for half baked.

I like your work its real life keep it up weell done.. ive just done a conversion on a ln111r with a ls1 in it just waiting for engineering. . By the way when your trying to rub of white board markers of your board use the same marker to go over your writing and it will wipe straight of.

ok question on rea rend i have 1997 dully 2 wheel drive power stroke. and the drum is behind meaning you have to pull the axle to change the shoes. is that how you can tell what kit to order?

Damn the amount of people that pointed out that you made a mistake in the title is outrageous. People quick to point out pointless issues as they knew what you were trying to say.

Fale: wave, waveband; a range of wavelengths on which eg radio signals are broadcast.

Fale? Lol...

Fale, pale, pail, ail, fail.

Fale,fail!

Fale 😂😂😂

What's a fale?

Fail?

Use fishing line 👍🏻 your welcome

Fishing line

I hit the end of the hub with a dead blow hammer, works every time

I just put my W56 back together yesterday. Didn’t do a full tear down. Bought it from a junkyard and just split the cases to inspect and check tolerances. Such an easy little part to work on once you get in there😂😂😂 today I’m doing the t cass! 😁😁

Use, braided spiderwire fishing line.

Heat gun....lol

Heat gun helps.

Heat up the badge with a heat gun or even a hair dryer loosens up the glue they use to stick on the badge. I did it with my accord letters and it came off easily just had a bit of leftover glue I had to scrape notbing big.

Part 2?

Harbor freight dental floss

Maybe fishing line next time?

Heat it up first! That’s how I got tags off my motorcycle

Heat it up first with a blow dryer and then use fishing line to remove the badge. You’re welcome.

🤤 "Promosm"

And it's great that all that dirt is in the cylinder now.

💯💪🏾🙏🏾🫵🏾

Break your Femur, and that's how they installed the rod and the same procedure to take it out. Good times.

Yop. Been done. Done it. They also make pneumatic removers that work on the same principal.

Genius!!!

Zinc/galvanized metals burn off some bad vapors.. careful bro