Video

Did you jack your truck up by the running board? Ballsy…

Could you give me a link for the bracket

Welcome to the bidet life! 💦

Awesome video, very informative. I just bought a 2000 and 2002 GTX Millennuim editions. Last of the two stroke models. About to tear them apart and rebuild. Fingers crossed.

How do you get the caddy off without taking the glass off?

I remember that you dont habe to remive the cassette to get the panels out. Remove the screws, get the window out and pull the Panels from the top.

MDF?! You got the nice legs and then cheap out on the surface? MDF falls apart! Get a nice butcher block counter top at lowes!

Did you get her finished up

Good job big boss 👍💯

Did it work?

Hi with 2001 gtx di seized engine its apart casing are in good condition now I'm wondering the cost of the complete list of parts and where to buy from any tips and maybe an over all cost of crank,rods gaskets and so on that I'll need to rebuild my engine $ ??

Do you have the paint code for the block?

Take a shot of Jack every time he does a lip smack

They sell specific shims to align the pump and are very very thin - way thinner than the washers you used in order to fine tune. You’re right to align the pump to hull and then pump to engine

There should be red loctite on the impeller shaft threads (or anti seize if in salt water)

Quick question for you. What did you do to the block did you hone it or anything like that? The crank did you cut it down or did you just have it polished?

*Thank goodness I’ve been looking everywhere for this*

I have never seen turf without adhesive on it

is slow AF and will gey annoyed pretty soon.

What app for the camera views ?

Rock on dude thanks for.the help my o6 750li has the same wire diagram

should remove feed tubes before removing injector hold down

The center cab mounts made of rubber are not a problem and don't need replacing unless you can't remove them like was shown in this video. If you can't separate any mounts then put on safety glasses, thread in the bolt into the stuck mount from the direction you removed it, then raise the body to apply pressure and hammer on the bolt head, they pop apart easily. The step rail on the cab is designed to support a person, not the cab. Lift on the cab directly with a 4x4 or similar. The step rails bolts can sheer and drop the cab on you when your hands are in a bad place. While pricey these are the better mounts to use, you could spend 20% of this cost and get mounts that will ride stiffer and may have loud squeaking noises, but anything is better than the factory mounts when they deteriorate.

Those turbo pipes aren't any good either way, might as well cut them. Someone who is doing this job will buy new ones anyway. There known to crack or break

I cringe every time I see a 6.4 on film being as I still have one.

What type of paint ? Gel coat? Acrylic? Lacquer?

Hey did you have to replace the rod bolts

salty drain water is a problem , in long run/future

Wow nice work

Where are you located? I need that template for the infinite baffle panel!!.. (I have an E60 535i... non-fold-down seats... I've already cut a pass-through, and I want to do two 15" infinite baffle)

Overall how difficult would you say this rebuild is? I've rebuilt motors for skidoos, but never a diesel motor, let alone something this big. I have a 2000 24v 5.9l cummins and was considering doing the same thing.

I'm on my 2nd RXDI rebuild. I just went through your videos and found an error in my last build which I was able to correct and my ski is running very well now. These videos are good quality visually and don't have annoying background music. I especially appreciate the way you clean your parts. Im kind of a freak about a clean hull. I'd like to gut my 2nd RXDI down the hull and power wash it, but cooler heads have prevailed as I don't want to disturbed 20+ yr old connections :) -- anyway this series is absolutely amazing and has helped me a TON!

Did you have to disconnect anything like the steering column?

Does it tell you if the salt is low?

is the paint on the plastic parts have to be marine?

Dude where’s the update vids for the Fummins install??!!! Can’t leave me hanging, brother 😮………… what’s the status?

Damn that engine bay turned out beautiful! Nice work dude. Now to go check to see if the engine install has begun 🤩

Where is da final vid

I'm surprised the bottom end is still in one piece and the block isn't cracked. Notorious for Coming apart in the bottom end.😢😢😢😢😢

Thank you so much!

What’s different between this an 2wd

Thanks for this almost gave up on mounting this monitor

😢 Cut the Turbo ✂️, Cut the motor mounts, then pay $3k to reinstall due to purchase of Rare 6.4L parts.

Why did you decide to get a new crank?

Did I miss the part when you installed the new seal?

I've seen 2 of your videos now and they both just end suddenly before the install is complete.. WTF? Its like you gave up making the video part way through the install and just published the video anyway... Thumbs down.. lame.

That shaft is so long because some sea doo have the engine at the front of the haul as mine does 99 xp 951

Thanks Man you showed me a lot take care.

I bought an aftermarket OEM and when I jump on a wave the bike turns off