Video

You just saved me $120 😅

About to replace mine. I just order it. Although it cost me $49 in amazon but thanks To this guy on the video, showing how to replace it.

When you were getting the tabs out I had a flashback of slipping while installing them had to go to medi clinic for stitches 😂

Putty knife to release top clips

Thank you so much for guiding me through these steps. It took me a lot longer than 15 minutes though! :D

Thank you

Thank you! I got this sewing machine from my husband’s great aunt but it had no manual with it. This has helped me get it threaded!

do the grill covers sit flat on yours? on mine the front divets they sit on are higher than the rear, the so grill covers are on a slope.

Awesome video! Just used this for a step by step and replaced mine in 30 minutes. Dryer works great now! Thanks!

so, speaking from a 2002 Sierra 1500, this device will do all the basic obd tool diagnostic functions, gm specific diagnostic functions and gm specific programming functions without the need for GM/ACDelco subscription software? Lets say i want to know if or why my hvac climate controller is not communicating with the blend door actuator controller, this would be the tool? or if I wanted to reprogram my BCM to turn off interior lights as soon as doors are closed and locked, or i wanted to program the bcm to keep fog lights on when headlamps are switched to high.. this tool can do that? can it do it without the two year subscription to GM/ACDelco SPS2?

Thank you for this video. I have the exact same mower, and I decided to get an additional battery. Same exact battery, but it won't run the mower, even when fully charged!! Charge and put in the old battery, mower works. Don't know what to do!!

Well done! Actually, I was able to hold the drum up while wiggling the heater coil tube out.

Just a quick thank you - this video saved my sanity. I had a similar box (not the exact one) and this helped me make sense of the crazy instructions. Appreciate it :)

I have same machine .. But I want to know if this machine sews stretchable fabric

I bought one of these new in 1981 from a sewing store. They said a school canceled their order for quite a few machines so they were having a sale on them. Used it for years. It is giving me problems and I was thinking about getting a new basic machine for around $100 BUT you have changed my mind. The Mrs there knows her way around a machine and she mentioned a few times that this is a good machine. I read the new ones have so much plastic on them. I am going to find a repair company and get it looked over and fixed so it runs smoothly. Thanks again.

Wonderfully helpful!! Thank you!!

I just found one of these at the thrift store and it’s in great condition! I’m very interested in learning more about the machine and how to care for it and use it. I really appreciate these videos! They are very informative and useful. Keep up the great work 😊

What can u do2 keep it anchored n safely attached?

Hello, the thread of my bobine doesn't want to go up with the needle and the top thread. I don't know what to do

Thank you. I have a White 1510

Is Lambs, a boy or girl⁉️

Perfect illustration thanks

Thank you so much! This is the first video I've found that clearly demonstrates, with up close video, the steps for threading this machine. I'm very grateful!

Thank you so much!! I was stuck at one point and your video helped me get through the setup :)

Got this job knocked out today. Thanks for the great vid. 👏

Hi...I Have the Same Dryer...But Mine...Turns Everything On But It Doesn't Spin...What Can It Be...😢🤔.. Can U Plz Help Me🥺

I can’t get the bobbin to catch the thread right and it jams 😢

Who did you buy it from?

Greenworks was dropped from my local John Deere dealership. Now I know why . Piece of $#@$

ty for such an easy to follow video and being straight forward. i'm setting up my moms old 237 and this was beyond helpful! thank you.

Sorry, but this video tells me nothing. What Pole goes into what Pole is what I need to know.

I got one for $35 from big W (Australia) it didn't have a tube from lid to soap...the nozzle didn't click on it just fell off with pressure..it came with some other little pick like but of plastic that I still don't know where that goes and it didn't soap up well and I used turtle wax soap for heavy duty cleaning...I ended up soaping the car then going over with a sponge and pressure wash off...I'm tucked off paying what I did but now I know there's nothing like elbow grease to clean the damn car 😆

How to buy this model

Same issue but also the plastic suction at the bottom came apart I don't think it's supposed to... I'm referring to the front clear plastic piece that says Bissell 6 cleaning rows dirtlifter power brush has separated from the clear piece it appears it should snap into or was glued into....? Should it snap back in or is this actually cracked off?

Thanks!

I was wrong it’s not Ethernet cabling. I’m not sure if 75ft is enough or if you need 150ft. It looks like the pole mount would work well.

How do u take the adapter off

My Freeman generator 7500 starts and runs for retreat of 4 seconds and then shuts down what is the problem

Une couverture COMPLETE d’installation … at last !, thank you !

Thanks for your chanel. I have the same machine. Never tried using until now since my Singer broke.

This is awesome....going to order one right now ❤

So helpful.. thank you

I’m building this grill now, but the side burner valve is missing. Not sure where I can get it, if you know?

Thank you for your time and to edit your video. It help me 100%. Thank you! Thank you!!

Thus is one reason why I got the version with a brushless motor

If your bracket that supports the heating element has the two screws behind, ratchet wrench with Phillips socket works wonders! Great instructional video with clear steps to get it done. Your video made what I thought might be intimidating, a simple repair. Took me a little over an hour due to the two bolts and my red/blue clips on the heating element took a while to get off.

Dude! Thank you! I found this old box and it was just taped into pieces and i could only get the legs the rest i couldnt figure out properly and your video saved me. Thanks so much

There is two greese fittings just be for the sickle bar connects to frame.

Thank you for putting the together - the instructions provided with the BBQ from Walmart get confusing towards the part when you have to screw in the valve. This video saved my sanity! Thanks again, will drop you a follow 🙏🏽👍🏼👍🏼

Thank you so much, I lost the manual and I wasn't sure what the spacers were