Video

❤

Running narrative while having it installed. Patient husband.

Bonded fabric blade is EXACTLY the same as Fine point blade. The housing is a different colour (pink) so that you remember it is for fabric.

Thank you so much for sharing the good bad and the ugly. It's important to know that everything doesn't come out. Perfect the first time and occasionally you have to drop back and punt!

Ooo this is doing more for me than I expected! I'm reconditioning an old Craftsman right now. Mine is rougher than yours (my neighbor kept it for a year or two outdoors under a tarp before gifting it to me), and I just got the table casting fully stripped, with the angle stock reinforcing the wings soaking in vinegar to get the rust off and a $100 order on the way from McMaster-Carr to replace all the fasteners I touched, which were all badly rusted and were occasionally stripped. The casting and motor/drivetrain seem good, and height/bevel motions came back nicely with some Boeshield, so I'm cautiously optimistic I'll have a machine that can do decent woodworking after hanging these hundreds of dollars of parts and accessories on this $0 table saw. First project will use just a miter gauge, and the Incra one I got looks very nice. Mentally shopping for a fence system to replace what came with it, which was probably iffy when new and is a joke now. Thanks for the video!

Thank you for mentioning to take the backing OFF.. I was so frustrated.. I bought the Freezer paper for the hack I saw but hey never said take off the white paper.. So my felt kept slipping.. You are fabulous.. thank you thank you

your picture is very blurry

Thank you so much for posting this awesome video! I have been pulling my hair out trying to transfer vinyl into a shadow box for my daughter's friends college graduation gifts. You are a lifesaver!!

I have found a rotary blade works great....I have never tried backing the material.

I can’t imagine taking an hour and a half on something that small. You definitely need to change vinyl

where did u go?

So if you now have it in design space you can use it from there and not have to go through scanning it again and using the eraser all around again? Sorry new to Cricut and learning new things

you could have put tape on back and your rotarty blade and it would have worked

OMG i feel your frustration. There is also a setting that makes the cricut go over the cut multiple times

@2:26. Its most likely your square. Cheap ones are not "that" square.

Do u have to convert image tomSVG file

Ridiculous that something this expensive has to be modified so much to fit. I wouldn't call it professional grade

You can't see what your doing

How do you get the machine to acknowledge you have changed the blade to the bonding blade ? My machine still thinks I’m using the blade it came with . I wanted to cut out some bonded velvet material . It wouldn’t give me an option . I bought the new blade , switched it over and the design site won’t show it on the process ??

Thank you of your post. This is exactly what I was thinking to use! What do you think of putting the shirt directly on the griddle w/ an iron on top. This would be instead of using a piece of wood and turning griddle over.

Where did you find the blade insert with splitter for that saw?

Anyone figure out how to get the stupid 11.5” limit to stop? So annoying.

I would love to make cute little felt pieces for my littles to stick onto a "felt board" but without using the bond paper 😏

Great tutorial, thanks. You mentioned a follow-up video where you use these cut images in a project. Could you please direct me to this.

Did you use the blade or the reg needle looking ones? Is the edible side down and did you have to mirror it?

I have a cricut 3 and I am having this exact problem.. Can you help me please ?

what is more frustrating is the blurry video lol

Why does my project say incompatible it says this project is not supported by your current machine selection. What does that mean

This helped me so much. I’ve been having problems with my cricut cutting the fabric. I loved that you showed your fails because I was having the same problems. I’m definitely going to try the fabric blade and see if this will help me too.

Great video and love all of your remarks lol :)

Mine says it is too big for mat so I save the image after I slice it and just delete that one that’s saying it doesn’t fit and cut the ones that do .. the ones that wouldn’t cut with the group cut by themselves if I make sense

i know this is an old video but now this issue is that cricut wont let me cut a plain card 8.5 x 11 why is that? how do we get arond this.

Hi, has anyone had the problem where your using a 12x24 mat (REART) on circuit maker 3 and it says “longer mat required” this is just for a simple htv project.

where is this felt from I love the corduroy look

⁴e p

Thank you for the video. I'm just about to tackle this project after putting it off for a year. I just installed the PALS system.

Not trying to critique, because this was a really good video! But when squaring the table and blade, you want to use the miter slots and adjust the blade via the trunnion. On the 113 Craftsman this can be a real pain in the ass! But well worth it in the end

Just bought this exact song with the fence system installed on Facebook for $200.

Very helpful thank you

Dislike

How did you get that??? It doesn't say that for me

Great job and explanation… you say what’s necessary to hear.. 😅 others talk too much. But thank you!

this question is for anyone that can answer it. I have a Delta 36-6013 table saw. the table top is 21 inches front to back. is there an aftermarket fence system that would work for my saw.

Thank you so much for your video. It helped 🤗

HUGE help - thank you so much!

As a newbie who gets frustrated trying this, I appreciate your honesty and being vulnerable. Thank you for showing us the compare and contrast (trial and error).

I just purchased a Cricut and found this video to be very helpful. Thank you so much!

Just ordered my fence!

Great video.. Really helped answer questions I had about this technique.. How do you price them?