Video

This is the best video I have seen and also with minimal removal of parts. I already changed the passenger side thanks to your video within 30min and planning to do the driver side soon. Looks like I need to drill out the mounting hole and come up with a nut and a bolt.

is this a box 5? if so which clutch do I need?

Great video. Perfectly made. Many thanks!

I love it but the offset would bother me

Best i have seen, brilliant, love from England UK 🇬🇧

Danke das hat funktioniert ⭐️⭐️⭐️⭐️⭐️

Can't seem to figure out how to get the heater core lines in through the firewall into the engine compartment

Great Video!!! Does anyone know the torque specs for the 2 bolts that are at the 4:29-4:34 of video?

Can I ask you a question please? What is that ring? You put back in the pan after you cleaned it up thanks. I enjoyed your video.

How much product did it take to do this top?

very helpful

I have a question about the power steering (Audi A4 B5), which makes a noise when the engine is running and you move the steering wheel even a little (the more the louder). Also, hydraulic oil is leaking somewhere, but I can't find the location for the life of me. However, the leak is so big that the expansion tank is almost empty within 2-3 minutes. Any idea where this could typically be on the A4 B5... ?

I saw that snappedbolt 😆 😆

You do realize that everyone of those parts have torque specs.

Hello. from which company did you use the coil and cables?

This is really one straight forward video of the process which is absolutely perfect! Keep up the good work!

Es hat super funktioniert. Dankeschön!😊

How did u get the middel two spark plugs loose I cant get even near them

Thank you for the video. I want to raise my my 2001 4runner 2wd only 2inch max without a suspension lift kit. It is only for looks. These 4wheel stores keeps trying to sell me into a 3 inch lift which I do not and will not do. Plus I do not want to change the geometry that much. I ask could I do exactly what I watch you do and they act like it isn't that great...What you did is perfect and less labor (less money for them). And it looks great! I will seek a mechanic to do the same....Great job and thank you again

Why didn't you explain how to remove the metal radiator hoses, the ones that are transmission hoses!!, I think the majority expected at least that!!!

Good job

I have Renault Clio 2007. It doesn’t shut off when I remove key. The engine keeps running. Please let me know what’s the problem in it?

It didn't make any difference on my 2500

my twingo dont close how to fix

you had a lot of work :), best regards from Poland

09:42 oh Gott , sie streicht die Polyhaube mit der Pinsel , anstatt mit der Lackierpistole und anschließend mit Klarlack und Härter . Was für ein Pfusch !?😂😂😂

Warum kein Aluboden , ihr Spezialisten 😂😂😂

Is my 95 rear end in my Dodge ram 1500 the same as a Dodge ram 1500 four-wheel drive 2001

Anyone know the shocks torque specs for top and bottom

Did you put the stabilizer link bushings on backwards in the one picture they are on backwards on the link? Over tightened for sure! Also there is a torque spec for the the pitman arm to shaft nut. I believe it’s 185 foot pounds. No way you got it that tight the way you were doing it. I would pull it apart and retorque. Actually take it to a shop and have them redo the whole job. You just should not be working on autos.

Awesomeness

Just picked one up. No Key. Any way tonstsrt it up without one to diagnose problems

Hi how many hours does it take to replace the clutch thanks

Brother child you put a link to the fuel pump !! And parts !!

Just do it I did it an it worked so if I can do it anyone can

I have a 97 A4 Quattro with the 2.8l, I'm hoping it will be a similar concept to this. I have a small seepage on the passenger side end seal thing, so I guess I'll just throw a new rack and pinion in. Totally a bummer, but oh well. I'm going to try running some stop leak in for a couple weeks and see if it improves it.

I own a getz year 2009. May I ask how many engine bases has and where? Thank you!

Just wondering if you need to somehow shut off the main gas supply on the tank side, before beginning to disassemble the reducer and disconnecting it from the main gas line? Or how does it work? Any insights into this question guys. Thank you.

Wat voor platen heb je aan de zijkanten gebruikt ik zie dat de vloeren betonplex zijn maar zijkant iets anders. Ga er zelf ook een opknappen deze video heeft heel veel vragen beantwoord. Thanks!

Good

Thanks for this video!!!

En español xf

nice music, nice work

Hey know this is 2 year old video but did you have to swap the servo valve when replacing the rack to the new that you put on ?

Great video, nice and simple to follow 😃

It’s definitely cool. But bugs me that the image isn’t centered. Was that adjustable at?

Dumb illiterate with two left hands. Read before you do something! He did so many unnecessary moves.

Good job ! Do a video on replacing a heater core in a 2012 Chrysler 200

❤❤❤

is that a 1.2i gasoline engine ? did you modify the oil thing to put metallic oil filter or its originally like this ? because mine and engines like this that i saw has the paper filter and the plastic cover