Video

She’s too cute! So funny the position she had herself in. :) 🥰

I am looking for a used plate mine bent were are u located in wi i no it"s shot but need one an can" t swing new just found your channel enjoying it

Just had to do the same thing to an L175 on the farm I work for. They are nice low profile machines and the super-boom is hard to beat

The pliers on the bottom side, or in between the handles works much better for grappling wire! As well as you missed a key feature while you were hammering those staples in with the pliers and holding it with your hands, you should hold it with the pliers and hammer with a hammer, that’s potentially saving your fingers from getting crushed. The two little holes in the “pliers “ are there to hold the staple while you swing the hammer.

You running fluid in the tires?

Your not supposed to add liquid to the compressor, vapor only alternate can fill valve 12 o'clock and 3 o'clock position every 15 seconds until can is empty.

What does this process accomplish? I'm asking as a complete city boy. Thanks

You got a vid on adjusting the front end?

Definitely giving the 826 a workout!

Цікавий культиватор, ніколи такого не бачив, в нашій зоні міжрядна культивація уже закінчилася.

Your corn looks pretty good. In SE Wisconsin it’s very spotty. We’ve had copious amounts of rain. Some corn is shoulder height and some is 3” tall…..then there’s some land that hasn’t even been planted

Your corn looks pretty good. In SE Wisconsin it’s very spotty. We’ve had copious amounts of rain. Some corn is shoulder height and some is 3” tall…..then there’s some land that hasn’t even been planted

I thought the cable was bad, but it wasn’t. I can hear a clinking noise inside when I manually move the rock shaft up and down. I suppose I need to go inside but I’m afraid to cause a problem I can’t solve when there might be a simpler solution. Wish I could find a video of a problem similar to this

just a footnote here i dont think you are supposed to be turning on your 4x4 on the highway on pavement at 40 MPH

Nicely done, saved yourself a ton of money by not bringing it to a shop somewhere

Great video. Gotta keep that 826 going. Those blind loads can be tricky, you would hate to damage something on a brand new pump. Where did you get the aftermarket pump?

I’d like to have the money you save yourself by fixing it all yourself….is there anything you haven’t fixed yet?

Wonderful Dairy Farm Video!!!! F+L, Corey

Great except for the banjo music. Made it hard to hear what you were saying and it was louder than the speech so it required volume adjustment.

Здравствуйте, какой номер подшипника на валах стоят?

A lost art form just like row crop cultivation… the old 826 still sounds strong 😉

Did you guys get alot of rain Friday and Saturday? We had 8 inches in s.w. Vernon county.

Thanks!

Love your channel theme verse! Farmcards, where in Wisconsin are you? I grew up in Gresham, near Shawano, along Hwy 29.

Wood gives you heat about 4 or 5 times... Cutting loading splitting stacking, then burning it. Similar to making hay, lots of steps

Thank you. This helped me greatly figuring out that strange lever/cable clip. It popped off, somehow I found it under the dash. Wouldn’t hurt to have a new one. Need to find that!

It’s finally that time 🙂👌

😳

I don’t think you have a bad attitude;) Kewaunee built some good stuff in their time

I'm curious about the hydraulic leak you have up front. I have a 3020 that has something going on up front as well.

Looks like you'll have to keep some spare u-bolts in stock.

Thank you for this! I have had an intermittent rattle/grinding noise in my 2017 F150 that mostly only happens at constant highway speed. When it randomly starts if i keep on the gas it keeps grinding and getting louder. As soon as i let off the gas it stops immediately then may start again in a minute or maybe half an hour later. it seems random. This is the first rattle/grind cause I have seen that isn't a heat shield rattle, which I doubt is the cause. This will be what i look into next!

Technically that gear is not reverse. Its forward road gear for a 4020 with a mounted cotton picker. With the picker mounted on the tractor, the tractor was operated in reverse. The operators platform was moved to the top of picker so it was steering a combine.

I’ve always liked the look of that 4020….you started haylage yet?

I did not notice there was a difference. Thank you.

Thanks for the video.

Thanks! Helped me here in Jamaica!

I was wondering when we’d see the 8630…. I spent a good bit of time in a TW15 when I was younger. Great tractors

Cold the white box be more annoying?

Aren't they a pretty sight.

We have. An 826 to and we also full throttle it on an ag bagger and has never done what your 826 did but is it good or bad but in know it's hauling a lot of throttle

We have a noble disc ripper the 4840 has broke a few shanks off, it’s also has no parts availability.

I was just through your area of the state a few weeks ago… it is truly beautiful out that way

Just wondering what your location is? I'm in Wisconsin as well

The 9 shank did pretty well. Those are things that are going to break eventually. Thanks for the video!

❤❤👌

❤John 3,16 ❤

John Deere Usually Handles sound equipment but When it came time for us to purchase Hay Equip, our first mower was sold by The J.D. dealer was A kuhn.... we kept it one year, sold it and bought a Krone 320 Easy Cut,,,,, WE presently have 3 mounted on KMC 4760 Caddies.... We average about 600 to 800 acres a year,,,, During the last 6 years of use we have yet to replace any roll pins in the cutter-bar protection system...... Our Variety of Hay has thin stems and slender leaves, so not much drying time is gained by conditioning....

Good looking calves. Do you keep any bull calves? Do you breed any to Angus?

That isn't tight dude.