mst3kpimp
mst3kpimp
  • 31
  • 336 556
LINDA BLAIR'S NATURAL VOICE IN "THE EXORCIST"
Here are some samples from the Exorcist featuring Linda Blair's voice before it was replaced by Mercedes McCambridge.
zhlédnutí: 11 018

Video

Window Leaking Clogged Sunroof Drain Fix on Nissan Altima 2014
zhlédnutí 14KPřed 2 lety
My passenger side was leaking from the roof, turns out the hose that runs from the sunroof drain to the firewall had a clog letting water backup.
Wet/Dry Shop Vac Filter Hack Cheap DIY
zhlédnutí 39KPřed 3 lety
The filter bag on my shop vac was coming apart so I replaced with some dollar store knee high pantyhose.
Easy RC Drone Battery Car Jumpstart
zhlédnutí 206Před 3 lety
Car battery was below 11v and could not start at all. Simple aligator clips wired to a 14.8v RC battery was able to easily start. Make sure you disconnect ASAP to prevent possible damage.
Quick Fix Stuck Car Hood Wont Open
zhlédnutí 38KPřed 3 lety
My 2014 Altimas hood would not open because of crappy dried lubricant no amount of yanking would work. Just slid in a paint stirring stick and problem solved. Make sure hood is fully closed before you pull latch the stick creates enough compression to help it pop up. Then re lube with some quality grease..
Gamo CFX CFR ACCU Reseal Tips and Mods
zhlédnutí 32KPřed 3 lety
Some tips on resealing and mods for the Gamo under-levers.
WEAK AC FIX! Nissan Altima SV/SL AC Compressor Refrigerant Control Valve Solenoid Repair
zhlédnutí 70KPřed 3 lety
I've had AC Issues on my 2014 Altima SV for years with delayed/erratic/reduced cooling and warm air at idle but it got worse recently. The problem is the solenoid in the compressor or ''refrigerant control valve" that gradually fails. The SV/SL models w/auto climate control have these Base/S models do not. A mechanic would prob have you replace the compressor but with a few tools you can repair...
Daisy 1200 Airgun BB Loading Window Mod
zhlédnutí 450Před 4 lety
Only the original run of the daisy 1200 had a window to let you see the bb's, my second run variant did not so I drilled a 3mm viewing hole. This prevents empty shots.
12 Year Old Godzilla Boy Drums Up A Storm!
zhlédnutí 99Před 4 lety
It's been 4 years since we've seen our favorite Godzilla expert and as you can see he's taller, thinner and more talenteder.
umarex makarov co2 power and trigger mod
zhlédnutí 7KPřed 4 lety
This simple mod solves the problem of weak power in double action and hard single action trigger pull on the all metal non blowback version of the makarov.
dc-4s charger problem error 7
zhlédnutí 48Před 5 lety
video illustrating the error 7 for banggood
CarQuest/Wearever Brake Clips Don't Fit
zhlédnutí 1,7KPřed 5 lety
This front wearever "platinum" kit PXD1650H from carquest are supposed to fit a 2014 Altima but the clips are poorly sized and even if you force them in the tabs rub the rotor resulting in screeching. The same brand rear set actually fit great. I ended up returning and got power stop z23 evolution's whose clips fit perfectly.
Stubborn Tree Sap Removal with Laquer Thinner
zhlédnutí 458Před 5 lety
My wheel had baked on sap etched into the paint, some I could scrape off w/a credit card but a few nothing seemed to help including tarminator, turtle wax tar remover, alcohol, spirits, wd-40 even gasoline. Lacquer thinner purchased cheap on ebay "not nail polish remover" on a q-tip applied for a few minutes was actually able to break it down. Understand it WILL leave a blemish where it is appl...
Altima Shifter Clicking Noise How to Fix
zhlédnutí 9KPřed 6 lety
My 2014 Altima's automatic shifter started making an intermittent clicking sound when shifting that seemed to be coming from the center console. I used the below guide to get at it and clean out. Probably some drops of soda accumulating over the years. Works great now. Disassembly Guide czcams.com/video/EU7vM2Y-7lY/video.html
HP Printer Paper Pick Up Repair C3180
zhlédnutí 12KPřed 6 lety
My old HP C3180 stopped picking up paper and I discovered one of the gears was cracked and slipping. Using the linked disassembly guide I was able to fix it. Just follow to step 22, you'll need to cut a portion of the rubber roller away so you can slide the gear over to apply glue. I tested some adhesives on the gear material which appears to be nylon, black plastic welder, JB weld, hot glue, l...
Vector SR48 w/Ft012 motor. Battery in rear
zhlédnutí 837Před 6 lety
Vector SR48 w/Ft012 motor. Battery in rear
Volantex Vector SR48 with FeiLun FT012 3500kv Motor
zhlédnutí 7KPřed 6 lety
Volantex Vector SR48 with FeiLun FT012 3500kv Motor
Vector SR48 Servo Problem
zhlédnutí 645Před 6 lety
Vector SR48 Servo Problem
Charsoon DC-4S Er2 Problem Lipo Charger
zhlédnutí 1,9KPřed 6 lety
Charsoon DC-4S Er2 Problem Lipo Charger
Multi-Flipping Fun With the Tarantula X6
zhlédnutí 48Před 6 lety
Multi-Flipping Fun With the Tarantula X6
Godzilla Boy is the Little Dummer Boy
zhlédnutí 79Před 8 lety
Godzilla Boy is the Little Dummer Boy
Custom Case & Stand for 1/6 Hot Toys Superman Chistopher Reeve Fortress of Solitude
zhlédnutí 3KPřed 12 lety
Custom Case & Stand for 1/6 Hot Toys Superman Chistopher Reeve Fortress of Solitude
Cape Forming on Hot Toys Christopher Reeve Superman
zhlédnutí 2,5KPřed 12 lety
Cape Forming on Hot Toys Christopher Reeve Superman
Band on the Run "A Different Take" Paul McCartney & WIngs
zhlédnutí 10KPřed 12 lety
Band on the Run "A Different Take" Paul McCartney & WIngs
Permanent Fix for Left Right Shoulder Buttons on DSI DS LITE DSIXL
zhlédnutí 68KPřed 12 lety
Permanent Fix for Left Right Shoulder Buttons on DSI DS LITE DSIXL
3 Year Old Godzilla Expert
zhlédnutí 415Před 13 lety
3 Year Old Godzilla Expert
Gary Busey Meets Supergirl 2010 Spooky Empire
zhlédnutí 1,1KPřed 13 lety
Gary Busey Meets Supergirl 2010 Spooky Empire
Gator dressed as the Devil animal cruelty VIEWER WARNING!
zhlédnutí 524Před 13 lety
Gator dressed as the Devil animal cruelty VIEWER WARNING!
John Carpenter Meets Lita Ford Spooky Empire 2010
zhlédnutí 759Před 13 lety
John Carpenter Meets Lita Ford Spooky Empire 2010
Dead Amish Guy at the Goodwill Sept 11 2010
zhlédnutí 5KPřed 13 lety
Dead Amish Guy at the Goodwill Sept 11 2010

Komentáře

  • @alangorrosquieta455
    @alangorrosquieta455 Před 2 hodinami

    would this fix apply if the mechanic states the compressor wont switch on?

    • @mst3kpimp
      @mst3kpimp Před 2 hodinami

      possibly so.

    • @alangorrosquieta455
      @alangorrosquieta455 Před 2 hodinami

      @@mst3kpimp ill try the repair soon, its worth the shot instead of spending the 1k for new unit

    • @mst3kpimp
      @mst3kpimp Před 35 minutami

      @@alangorrosquieta455 indeed, please let us know how it goes.

  • @ChristiElekes-sd9yh

    Thank you, my hood is fixed!

  • @THX..1138
    @THX..1138 Před 4 dny

    I make a bag out of paper towel with duct tape.

  • @TrippyG.
    @TrippyG. Před 8 dny

    Would a bad solenoid effect condensor fan speed?

    • @mst3kpimp
      @mst3kpimp Před 8 dny

      in a sense since the fan kicks into high speed when the ac hits a certain pressure so if the solenoid is affecting that it can affect the fans as well.

  • @username10
    @username10 Před 11 dny

    Thank you, have a nice day

  • @frankfails8347
    @frankfails8347 Před 20 dny

    Thank you.

  • @TaquitoNetflix
    @TaquitoNetflix Před 28 dny

    Hello bro

  • @accurateapplianceelectroni9703

    I have the same problem on my C7280. I used Hardman epoxy orange and it bonds well to nylon.

    • @mst3kpimp
      @mst3kpimp Před měsícem

      oh nice i never heard of that product.

  • @mst3kpimp
    @mst3kpimp Před měsícem

    no only sv and sl

  • @blackout260112
    @blackout260112 Před měsícem

    Does the s model have the same setup?

    • @scottcampbell1552
      @scottcampbell1552 Před 7 dny

      I have a 2009 S model and it has a mechanical control valve with the manual climate control. No wires as it uses an internal bellows in the valve to try and maintain suction pressure. The variable displacement compressors need a device like this to change the angle of the swash plate inside the compressor. The Valve is in the housing facing the engine block so it isn't easily seen (on mine), held in by a C clip. As the evap temp drops because the cabin is cooling, the TXV reduces the amount of refrigerant flowing into the evap which also means lower pressures on the suction side of the compressor. The valve responds by decreasing the angle of the swash plate so the compressor isn't pumping as much. As the temp load on the evap increases (or is already high) suction pressure will be high, TXV opens more to flow more refrigerant to the evap and suction pressure is high, so the valve increases the angle causing the compressor to pump more. This is constantly changing as temps change.

  • @iranpagan9081
    @iranpagan9081 Před měsícem

    Thank you!!!

  • @letsgokyle7103
    @letsgokyle7103 Před 2 měsíci

    Jesus Christ god bless you thank you.

  • @lips12925
    @lips12925 Před 2 měsíci

    This worked perfect. A Big Thank you, from Ireland

  • @awadahmed3074
    @awadahmed3074 Před 2 měsíci

    Thanks, it worked.

  • @grantp4022
    @grantp4022 Před 2 měsíci

    I have a problem with hood stuck closed as well. Now it may be from the latch under the hood being rusted shut, or the hood frozen shut as I live in Canada, and it's just starting to warm up. I haven't had the hood open in about 2 years, so it's possible the latch rusted shut ? It's an older 97 Chev Lumina, but a great utility car, that I'd like to keep. I was thinking of firstly waiting for the weather to warm up, and see if the problem was the hood or latch was frozen. If that doesn't work, then I'll assume the latch is rusted shut, OR the cable is broken. If the cable broke ( can't see why) then your method would not work. Any ideas for me ? Good video BTW :) How would I know if the cable is broken ? Go by feel ???

    • @mst3kpimp
      @mst3kpimp Před 2 měsíci

      I read a post from a 98 lumina owner and the problem was the cable sheath plastic end behind the release lever was popped out of its' bracket. Without light under the dash, you can't see it. Popping it back in apparently corrects the issue.

  • @burnlastsunday
    @burnlastsunday Před 3 měsíci

    My release works fine... It pops. Up but won't open or close

    • @mst3kpimp
      @mst3kpimp Před 3 měsíci

      try pushing the hood in until it clicks then you can release with the stick in or just pry up with your fingers while someone releases the latch.

    • @burnlastsunday
      @burnlastsunday Před 3 měsíci

      @@mst3kpimp Pushing it in? How do you mean? My friend opened it for me six months ago with a pry bar... Said the release got bent... But I can't figure out how to do this on my own.

    • @mst3kpimp
      @mst3kpimp Před 2 měsíci

      @@burnlastsunday oh if was forced open with a pry bar that may have bent the mechanism youll prob have to pry it open again just to see whats wrong ect.

    • @burnlastsunday
      @burnlastsunday Před 2 měsíci

      @@mst3kpimp Yeah it has been totally fine up til a couple days ago now I had to mess some just to get it shut again. But I need to do something I'm almost out of oil(Camry)

  • @marcosmecatronikify
    @marcosmecatronikify Před 3 měsíci

    can this valave be changed with full lines? or it is always needed to empty them?

  • @Raven_Sekou
    @Raven_Sekou Před 3 měsíci

    Same problem except the release button was broke. How do you get hood open when release button doesnt work at all

    • @mst3kpimp
      @mst3kpimp Před 3 měsíci

      behind the release lever you should see the cable, you can pull on it with pliers.

  • @leapcoin9226
    @leapcoin9226 Před 4 měsíci

    Appreciate the sage advice. Road trip Ready now. You Rock!!!

  • @yukun-thomassui3442
    @yukun-thomassui3442 Před 4 měsíci

    really helps, Thank you

  • @krzysztof4068
    @krzysztof4068 Před 4 měsíci

    Awesome, thanks!

  • @anthonyi4543
    @anthonyi4543 Před 4 měsíci

    Life shaver. Used a plastic shim. Popped right up. Blasted the mechanism with half a bottle of WD whites grease!

  • @jimb2868
    @jimb2868 Před 4 měsíci

    I used a hole saw 3 inc to cut a hole right under where the gear is on the bottom side so I can work better, it worked great. easy to work on then sand the hole inside the printer so the paper feeds just use about 20-30- pieces of paper and it feeds great took me 1/2 hour and shes been ok for 50 pages printed so far good luck.

  • @vaneharris8947
    @vaneharris8947 Před 4 měsíci

    This worked I used a wood ruler. Thank you!!

  • @quierras
    @quierras Před 5 měsíci

    Oh my freaking good, thank you and thank my bf for having random things strong wood laying around, thank you

  • @jingledfriskies5048
    @jingledfriskies5048 Před 5 měsíci

    This video is 12 years old, but it still helped me a ton. Thank you very much.

    • @mst3kpimp
      @mst3kpimp Před 5 měsíci

      oh wow, i honestly forgot i made this!

  • @braindeadmikelarsen4288
    @braindeadmikelarsen4288 Před 6 měsíci

    Extremely helpful, thank you ‼️

  • @ChumpPump
    @ChumpPump Před 6 měsíci

    what lube works

    • @mst3kpimp
      @mst3kpimp Před 6 měsíci

      most kinds or auto grease.

  • @lennoxwelds
    @lennoxwelds Před 6 měsíci

    You just saved me ty

  • @latanyahall300
    @latanyahall300 Před 7 měsíci

    Whoa see my car has been sitting at kroger for the past 4 days bc I can't get the hood open. Thank you soo much I'm about to try this!!

  • @jaredresnick3437
    @jaredresnick3437 Před 7 měsíci

    What type of lubricant? Not sure if I'll need it but right now my hood is stuck as well

    • @mst3kpimp
      @mst3kpimp Před 7 měsíci

      you want some thick auto multi-grease

  • @Youthman
    @Youthman Před 8 měsíci

    I literally had the exact same issue with mine. Thanks for the tip. Worked like a charm.

  • @TheRockIsCooking
    @TheRockIsCooking Před 8 měsíci

    W mans it worked. I had to use a spatula

    • @mst3kpimp
      @mst3kpimp Před 8 měsíci

      cool, i had it happen recently and was able to use my fingers on the side.

  • @perezmiguel7463
    @perezmiguel7463 Před 8 měsíci

    I did what you did and it really helped when it rains a little or when i wash my car, but when it rains non stop the roof and the floor get really wet. Does that mean I probably need a new seal?

    • @mst3kpimp
      @mst3kpimp Před 8 měsíci

      are you sure the water has a clear path to drain through? it sounds like its backing up with heavy rain. maybe disconnect the tube and push lawn trimmer line down until it comes out the other end you could have further obstructions.

    • @perezmiguel7463
      @perezmiguel7463 Před 8 měsíci

      @@mst3kpimp yes its my second time checking and still got wet after fixing, I checked and both paths were clean but water was still getting in with only non stop rain . My last guess is that it probably needs a new seal around the window

    • @mst3kpimp
      @mst3kpimp Před 8 měsíci

      @@perezmiguel7463 maybe but I feel like theres a buildup at the exit port that is preventing full drainage since your getting wet floors to.

  • @Adgegbe50ag
    @Adgegbe50ag Před 8 měsíci

    My guy you just saved another person here. My battery died on me and hood won't open but this video helped. Thank you for this video❤

    • @mst3kpimp
      @mst3kpimp Před 8 měsíci

      oh awesome so glad to help, btw you can also just use your fingers on the sides to lift it open after you pull the release.

  • @rodrigodasilvacarvalho6890
    @rodrigodasilvacarvalho6890 Před 8 měsíci

    Thank you so much. My passenger floor was flooded. I followed all your steps and it all worked perfectly. But I did not make that final test in the end. I hope everything went fine. Also, do we have to do this for the driver's side as well? I am afraid now. 😅

    • @mst3kpimp
      @mst3kpimp Před 8 měsíci

      glad to help, so far i haven't had this problem on the drivers side, from what i can see on youtube its better to do it from inside the hood.

  • @musiegebremariam2123
    @musiegebremariam2123 Před 9 měsíci

    Thank you so much really work!!

  • @m1chau007
    @m1chau007 Před 9 měsíci

    That worked, thanks a lot!

  • @bubbajones4522
    @bubbajones4522 Před 9 měsíci

    This should have been a recall with all the failures.

  • @dragonfoxsolid1308
    @dragonfoxsolid1308 Před 9 měsíci

    Yeah do physical labor while Jews take your money

  • @alecianicole3012
    @alecianicole3012 Před 10 měsíci

    @OWK000 I was thinking maybe dryer sheets under the pant hose. Lol. They too are breathable... And the smell good too. So I'd assume it'd work like an air freshener while also acting as a prefilter. Lol. I'm all for dual purpose items... Especially ones that smell good. Lol.

  • @mst3kpimp
    @mst3kpimp Před 10 měsíci

    Maybe a bad clutch, not enough/too much coolant or a malfunctioning expansion valve.

  • @kevinpaulroberson7305
    @kevinpaulroberson7305 Před 10 měsíci

    What could the problem be if you have these symptoms in a S?

  • @robertfezekas6632
    @robertfezekas6632 Před 10 měsíci

    Update! That was the problem! Thanks for posting the video. Obviously you helped save my family alot of money! Thank you

  • @robertfezekas6632
    @robertfezekas6632 Před 10 měsíci

    Thanks for the video! Couple of set backs: Parts place sold me the wrong part. The gauge kit I rented didnt have the low & high side fittings. Shame on me for not checking before I walked out of the store. Other then that...new part should be in tomorrow. Ill know if it fixes the problem then. Ill be sure to post!

  • @VunderGuy
    @VunderGuy Před 10 měsíci

    You do understand, no amount of Barbie simping would save you if you simped for a movie so blatantly Misogynist that was really popular, right? No amount of 'boy power! Yah!' or 'muh satire' would save you from being torn apart and eviscerated in every way possible by the feminist hordes, right?

  • @VunderGuy
    @VunderGuy Před 10 měsíci

    Level 7. Call the precise and verifiable destruction of their Simping longwinded when it's literally less long winded than all the times the Barbie movie ultimately just said, 'Men bad, m'kay.' And Warnber Bros is STILL not going get out of the red with everything bad happening to them long enough to get Barbie 2 off the ground before they go under. XD

  • @alvaro93364
    @alvaro93364 Před 10 měsíci

    Hey, I replaced the AC compressor, which means it has a new switch/sensor but it still does the same thing. I'm going to replace the expansion valve to see what happens.

    • @mst3kpimp
      @mst3kpimp Před 10 měsíci

      odd, please keep us posted.

  • @VunderGuy
    @VunderGuy Před 10 měsíci

    5 Levels of Barbie Simping 1. Ignore the deceptive marketing and that the movie's box office results is WB marketing's victory and not the actual film makers to the point where all of them really should get bigger raises than the actual production people. 2. Conveniently ignore WB's stake in Rotten Tomatoes and them boosting the ratings for this movie and bringing down the ratings for Super Mario. 3. Conveniently ignore that this movie is quite obviously suffering from Force Awakens syndrome where the target audience has been so neglected for chicflics that they're desperate for anything billing itself and pretty and pink. 4. Conveniently ignore that WB is still in the red with all the stinkers and flops they've put out and are going to put out to the point where even if this movie does exceed Super Mario Bros in overall gross, they're still in an ocean of money problems without so much as a paddle and they're nowhere near as big as Disney so they really can't afford flopping so much. 5. Conveniently ignore that an alleged sequel is many, many, MANY more years away than would be typical because of the writer's and actor's strike crippling Hollyweird right now to the point where the sequel will probably be 4 years in the making and well and truly far away enough that Warner Bros might not even exist with its mounting debt and thus can't make the movie.

  • @dragonfoxsolid1308
    @dragonfoxsolid1308 Před 10 měsíci

    Zionist pawn.