Video

Not true. I use one and had great results. All the things he said were true, however if you know what to expect it’s easy to do. I don’t jam the auger blade in, I “float it” and dig by “feel” it takes longer but absolutely works

Wooder??

What consistency are you aiming for if you put 1/3 bag of concrete then pouring in water?

Aluminum should not be set in concrete as Aluminum reacts with the alkalis in portland cement producing hydrogen gas, causing corrosion on the aluminum fence posts. I contacted Sakrete and Quitrite and both companies confirmed that aluminum and concrete are incompatible and not to use it on aluminum fence posts, they will eventually corrode. I used Fast2K Foam Deck & post anchor on my aluminum fence posts. Dug down past frost line bell shaped the bottom and installed 8” of fiberglass rebar thru the post near the bottom of each post making a x so the post had legs. No chance the posts will ever pull out of the foam nor will the foam ever come out of the hole with the bottom larger than the top. Posts survived an Illinois winter and didn’t budge. Foam sets up in minutes.

👍👍👍👍👍 Good video

ok but how much concrete to fill the inside of 9' gate post?

Great video, very helpful. Thanks for this.

If you're mounting the fence on top of the pool deck of an inground pool what is the distance from the outer edge of the pool deck to the fence?

It's so much easier with a post level vs. torpedo level

How deep in Columbus, OH? 30”

My gate has settled after 6 years. How do you adjust the gate so it lines up again?

'Promosm'

This is the type of guy who literally CAN'T do the work but talks like he knows

thank you random small youtuber

Watch the full video by clicking: czcams.com/video/U2iziiyKjtE/video.html

Watch the full video by clicking: czcams.com/video/U2iziiyKjtE/video.html

Watch the full video by clicking: czcams.com/video/U2iziiyKjtE/video.html

Watch the full video by clicking: czcams.com/video/U2iziiyKjtE/video.html

Watch the full video by clicking: czcams.com/video/U2iziiyKjtE/video.html

Why are you putting it only in dirt? It should be on a solid slab (sona tube) of concrete. Not in but on. Your fence will now move around over the years, warping and sagging. Good job making a video that shows you do not know how to install a simple fence post. Go back to your cubicle, leave outdoor work to the pros…..

Awesome video! I’m finding this a couple years after you filmed it. Quick question: At the end, how did you hammer that post deeper to get it level after you already wet poured the concrete? It was still workable after completing the entire fence?

Good video. I used the Swanson Tool Co PL001M Magnetic Composite Post Level, Yellow, Includes Elastic Loop for Hands-Free Work and 3 Vials for Easy Plumb and Level Reads

Wtf is wooder

What if you are installing 200ft and the ground slopes downward. Is this type of fence still a good option?

when using a crowbar start from the center of your hole and work out to your edges

short and well explained.

Thanks for a very helpful video! I just finished installing my pool fence and used a lot of your tips. In particular were the ones for the gate. They kept me from messing it up. :)

I just can’t believe the home owner left that shitty deck work for later, he need it to do it at the same time as pool before the fence went in.

If you're doing a job that big should have used a post digger wouldn't have been so tied, but looks good

It looks amazing.

are you even mixing the concrete with water?

i read that you shouldnt use concrete with aluminum fencing because itll cause a chemical reaction and erode the aluminum

When using a digging or spud bar, USE GLOVES. That heavy bar will tear up your hands, especially if you don't do a lot of manual labor. When applying the hinges and latches, to make sure the self tapping screws don't wander off the point that you want them, use a center punch or small drill bit to have a dimple exactly where you want it so the hardware is exactly where you want it. You can also use a circular saw to cut the fence, just use a metal cutting blade. Put painter's tape over the fence so that the saw won't scratch the paint or finish of your fence.

What kind the screws you put? Where can I get it? Thanks you vídeo it’s amazing, today I’ll make my first aluminum fence.

And you use the concrete the correct way good 👍

Thanks you !

Great video !

REGULATIONS IN Australia is the latch must be located pool side.

How’s the cap going to go on the latch post.

I think you meant because of the “planDEMic”

His level is questionable size

What is the distance between each hole for that fence?

How's this working out?

If you concrete the posts in, how the hell do you replace a panel if you need to?

Question: So you can leave the concrete dry in the hole? Or do you add water to the concrete once it is in the hole?

Fantastic! I am gonna do my fence and this is a great video for me! Thank you.

Great job

Gracias amigo muy buen video

When you come down the steps @19:19, there is about 5' of open area to get in the pool- is that pool code? Seems like there should be some type of "barrier" to stop kids/animals

I like how you put the customer to work--bahahahah