Video

But if you don’t have a claw this is the way 😉

Big time 👍😎

If you don’t see the importance in this video then that’s ok, thanks for watching

Totally make great and valid points. I do like to build things a little bit overkill and I have done a lot of insurance build back work on roofs that were built with non-galvanized nails had a lot of rust and repair needed due to water getting below the shingles for a long time, and if the nails were galvanized would have lasted longer, but yes, not really necessary but I still do it like that. Thanks for your two cents appreciate the feedback 👍

He definitely gets paid by the hour, lol But totally worth it.

🥴

Very well said 😎👍

lol you’re very correct but the rough opening wasn’t done wrong. There was some temporary two by fours up there to hold some plywood to have the opening temporary closed off. But they threw one too many nails in that temporary 2 x 4 that’s for sure should just been two nails halfway sunk, but instead there was like six fully nailed in. 🥴

Round hammer 🔨 😂

@@co-know-proconstructiontipshe saying us the claw to pry the board off instead of swinging at a wedge 20 times

😂😂😂😂😂😂👍

hey, a broke carpenter still needs to get it done then they can get paid and buy that cats paw 😉 if you only have a couple wedges of wood. This will get it done. 👍😎💪

@@co-know-proconstructiontipsbig facts! That money ain’t just for that white party powder

Thank you very cool. Appreciate the feedback and support man really cool. 👍

Thanks so much 👍😊😎

Yes it is A RYOBI Wood Door Trimmer model: A99DT01 from Homedepot 👍

Absolutely no problem. We’d like to wear a mask on these old houses when we’re kicking up dust and that day there was some work going on in the rest of the house that was pretty dusty. We wear a mask all the time on most of our projects. It’s just how we roll working on these old houses there’s a lot of dust you can’t see in the videos, but we can definitely see it on the project. thanks for the comment. Glad you like the vid. 👍😎

Great question, i’ll print out a new set and do the same thing. Small jobs not to many if any really get any additional plans added that’s typically a bigger job.

I used to have one i made in a similar way but using bolts, it's also works to hold your carpenters square at a specific angle if you give it a straight edge

nope unfortunately , it wasn’t even good enough to finish off all the rafter tales had to pull out the old trustee palm sander, which is a quarter of the weight of this Ryobi Hoopty tool I do not recommend. 😎

Thanks for the comment👍Do i know you?

@@co-know-proconstructiontips Nah, I just follow your channel and learn a lot. You being from California sparks my interest because I want to learn more about the residential construction here in LA. Any extra work I can get would be great.

lol exactly

Basically but when it’s a GLB specs call out 5-1/4 by 15 inch exactly with a 1/2 inch camber in the mid span. 👍

That’s how you do it 👍 we didn’t rent any Block and tackle we just used a Husky ratchet strap as our block and tackle. Worked out great 👍 Thanks for sharing your experience sounds like a great build.

@@co-know-proconstructiontips The ratchet strap is pretty good idea too

👍😎💪 I Bet you could!!

awesome you are so welcome

Big time, i like the way they can be used in so many different ways it’s crazy.

@@co-know-proconstructiontips Big time like the way you guys put that material lift in the back of the truck that was awesome 👏 Iv done that a few times myself 😊

🥴👍

🥴💪

Well if you don’t know how to frame a window or have not seen one framed before. This video might help people understand how to frame a window. At least the process. 👍😎

@@co-know-proconstructiontips fair. I was just expecting some info on things like how many nails to use, best wood cut, etc.

That is really really really good feedback thank you and I appreciate your comment. Hundred percent. 💯 we will definitely start upping our tips and information. Our goal is to spread construction knowledge and basic stuff like that is very important. Very cool. again thank you for taking the time to leave this cool comment. 👍😊

@@co-know-proconstructiontips you're welcome, and thanks for taking the constructive feedback! Keep up the good work 👍🤙

If it was your house then you would have a badass house. We are adding a second story to a 90 year old house. This video you commented on is us adding an under pad we underpinned to the existing foundation. During this process we noticed some of the old floor joists were crowned with big hips in them that caused the existing floor to have higher levels than the rest of the floor. So before we added our new subfloor plywood we hit the high spots with a skill saw Kerf technique then we smoothed out and leveled with a power planner. The final product is awesome level subfloor. Even though this section is going to be under the new washer closet we still wanted it level. Thanks for the lame comment lol

it shouldn’t worry you at all what worries me is that it worries you 😔 Lol in your logical mind. This is lame and isn’t used but every Framing crew on the planet does this you just may not see it but it’s done. All good 👍

@@co-know-proconstructiontips and I seen worst I did remodeling for 15 years but we only did high end remodeling so most times there was not repairs but redo, and when did repairs we had to do as pro as it could be. but people will always try to fix stuff the easy way, I used to build guitars like in that trade you can't do stuff like that. ha in an old deck if the customer don't care then so be it

appreciate you👍😎

thanks for watching anyways appreciate the comment 👍😎

🥴

Thanks 😊 we can build one for you it’s about 1,300 to 1,800 for the build. And this price does not include shipping. We are out of Burbank CA if your within 30 miles from us we can dilever. 👍😎

Yup after we bring the material down with the saw we smooth out with a power planer. Standard drill

Thats awesome i was 8 when i learned how to kerf wood with a skill saw. Dad’s a builder so would pick up some skills on the weekend when i would go with him.

Thanks 😊

Go feed some snakes 🐍 buddy you don’t know what you’re talking about 🥴😂

You can do it 👍

@co-know-proconstructiontips the orange cover stays but the ehrernet/coax plate screw doesn't seem to be grabbing. My other concern is the cat 6 and coax cable may be too long, inside the wall, and may push on the plates in the adjoined rooms, lol.

Thanks DTC!! 👍😎

Great craftsmanship can be seen and appreciated in even the most basic. Taking pride in every aspect of work will allow the final product to truly speak for itself.

🥴

@@whaleofawomanGreat comment 👍🏻

Na😂

Thanks for this awesome comment!! Appreciate you 😎👍💪

We love the 3 stringers so strong 💪 also there 3x14 so very stout. So true on the stringers splitting great comment thanks for sharing your experience.

I totally feel you man these pieces of 3 x 14 were actually very square. The edges were almost perfect 90s. 👍