Video

Do you need a Ethernet connection I have my printer in the garage and to connect to internet I need 200ft cables

love your software has been running my 2 in home printers for 5yrs now

klipper Does it work the same way?

Meine sind von der Qualität her immer extrem verpixelt… obwohl ich eine FullHD Kamera und gute Beleuchtung habe. Gibt es irgendwelche Tweaks die Videos zu verbessern? Ich denke mal dass es an der komprimierung des Videos liegt?

I recently bought a Prusa Mini + with built-in wifi module, can I use this software instead of Prusa Link?

Wie stelle ich das beim Repetier ein, dass ich so einen smoothen Zeitraffer bekomme? Meine sehen einfach nur schrecklich aus.

is there anyway to have integrations with repetier server? Our company has multiple printers, and we want to push information to another data hub to store and organize everything. Is that possible?

The best 👍

Where can we find a changelog. It seems I cant view that directly on the server unless there is an update.

nice video

Smother print with warm marshmallows. Got it. Thanks.

i have no tool tab section on my software or nothing that says bed heat map, i downloaded your version and i dont even see it there and the new update dont have this feature whats going on ?

Love your work. Thank you very much.

How to do this with the Cartesian printer?

Dear respected sir, I am using a Diamond 3 in and 1 out nozzle where I will use 3 color. Here you have shown the tutorial for 2 color. Please sir if possible, could you make tutorial for 3 color Repetier setup? I am facing some problem.

My configuration.h is the same as yours except dimensions differences including rods length, radius etc, other than that the corrections and leveling are set to the same as yours, but g29 measure only 3 points like other users and g32 s2 measure a grid, what's wrong with my firmware?

not perfect

followed all the steps up to running the first bed leveling routine G32 S2. The printer tested some weird points, tested the centre twice and then a point slightly off centre. After this is did not home again and spat back NaN for all 3 values in the host, and told me autoleveling was disabled. After that all my steppers refuse to work at all. They will turn on for about half a second when the machine is reset or turned on but nothing after that. Printer will also hang if told to home axis. Any advice will be appreciated.

Love the video! I have a question though. When I use Height Map my starting point is X -110, Y - 60. When I run my G33 command it starts at X -110, Y 60. How do I get my G33 to run the same path as my Height Map, or does it even matter what path my G33 starts?

Any idea how to hook up the limit switch for this type of bed leveling on a MKS Base 1.4 board?

Nice, what's that fan holder on the printer? I got that printer too without fans and want to fix that. Is it something from thingiverse?

my 3d printer wont connect to repetier

You say g29 measures 7x7 points. Mine only measures 3 points defined in EEPROM, and the log never shows any correction information. What am I doing wrong? Repetier 0.92.9. I have also tried g33, but it says it is an unknown command.

how do you put that square figure in the bottom????

How to calibrate dual nozzle for Z height??

i never knew you could select and drag to join the stl files. ive been zooming in and aligning them badly and i even made a checkerboard alignment to add to my models. thank you.

How to config repetier for color print? +Repetier

yes, can you upload your firmware you used, my printer keeps trying to read off the build plate during the bed height measurements and causes the hot end tip to drive into the bed and make the belts slip and hard crash.

better now! the bed heigt map on the tool tabs in repetier is grey and unusable... Do you know why??

How long is the rod you used to get the axis equal height?

the m99 x0, m99 y0, m99 z0, and g132 s1 commands dont do anything for me! please help ive been having this problem for some time now.

Hey, great video, is there a automated method to correct the endstops without the rods eg with test points near the towers?

thanks for your video! but on my "show in log" I've never seen "zCorr: ..." and all the operation seems do nothing... (the Zmin and Z max stay the more or less the same) Also on my show in log there is everytime T : 20.56/0 @:0 Echo : M 105 wait ok ... who repete all the time... Do you know what I do wrong??

hello, when i enter G29, it only goes to 3 point(different from you) and so how to add the correction factor in it ?

Having problem with my delta printer!! Everything is ok until the g29 command. It wants to go to these coordinates X7562 and Y 6894 ??? Does anyone had the same problem ?? What should i do ??

what kind of delta is this?

Once this is done, is it permanent? Or does this have to be done every time you print?

Good techniques, would have liked to see is sculpted.

What materials / tools have been used in this video?