Video

Had the same problem, it was the powder Cascade, I have used this brand for years. I changed to Finish quantum tabs and problem solved. Never go back to cascade again

Throttle Position Sensor.

mine smells awful from living in the desert for years. all the dust has just built up and there's no way to reach the Evap to clean it.

Great job! You can also use Mr. Clean eraser, that cleaned my son's white helmet with ease.

Did you find the problem

I've watched a lot of these videos tonight and after doing so wondered if a simple SOS pad would do the trick. Thanks for the demo!

The wind overpowered your voice. Mostly unintelligible. Two choices, get a microphone with wind shielding, OR add the narration while editing the video.

Great tip…I will try this.

Great Videos! Thank you for sharing. A can of Silicon spray to spray across the channels before sliding the new seal in is a big help. Just a suggestion. Thanks again, your video's are very helpful, nice job!

How is your farmsink? I was alot of complaints about the sink cracked and chipped.

Fixed the problem, bought 2 actuators and same problem, I opened the old one to see what was the problem and after studying the actuator, I saw that the contact pins on the black gear would barely get out of the contact board making the problem of not opening or closing. I rolled up small rags to zip tie them to the plastic rail on the blower motor where the vent door rest, set the actuator to the middle, installed everything back and works like new. (The rags stop the inlet door from fully opening so that the pins stay on the contact board)

Perfect video!! Mine had a horrible rat smell! Turns out they nested up under the windshield air intake. Had to remove the plastic grille and got a water hose in there to get everything out of there. A little water made it in the cab, luckily rubber floor mats caught the piss water. I soaked the evap coil and intake ducts with green clean and will get after it tomorrow again. That’s what happens when you let your truck sit I guess!!

Good deal bud thanks

This comment has nothing to do with your current video, so I apologize in advance. But I was curious if you could help me with how you converted your kids sehomy tractor to a 18v battery? Thanks!

Mushroom roots typically grow in rings, this is just nature being nature.

You should make a finish/ follow up video on this, bro!

so it is a year old - how is it holding up

I was interested in the topic but got sick watching

Spit it out man.

You are the man! My vehicle popped up with all the images! Thank you so much, this was a very informative video.

There's an abandoned truck just down my street and ironically the dash is perfect. Heading down there now😅

Thank you for sharing this information. I'm dealing with the same problem tryna match paint for my machine.

What are you doing? You can’t get the pen to come out the slide the shaft out I’m having that problem with mine now.

thank you for this my Dakota has horrible bedrock and I'm going to give this a shot I'm guessing thank you for this my Dakota has horrible rot in same spot

Every wax ring that has a horn, when I remove the horn is cracked. Every. Single. One. And yes. Like all you guys, I’ve changed out a lot of comodes.

Awesome

Thanks for the video. I'm cleaning my son's helmet too. I'll try the nail polish remover.

Reminds me of a video of a truck that had a hung open injector.

I just picked up some cub cadet paint at tractor supply. It didn’t look very close inside of the store but when I looked at it in natural sunlight outside of the store, it was a much closer match. Hopefully it’ll look even better once on the mower.

Great info,thanks.

I’m glad you got it for $10,000 less

My dishwasher has a dog smell lol

That my friend is a called the blower motor resistor module

Ariens is pronounced like Erins, not like Aryans. Hell, just watch some of their own videos.

Mine is doing the same thing intermittently, but it blows black when you give it lots of throttle. Did you get it figured out?

They actually never removed the mortice lock that part you were referring to is the mortice joint that holds the door together

I actually did mine last night and I use an orbital sander with a 40 grit sandpaper took it right off in less than 10 minutes. I had it done with no damage to the surface underneath.

Is tr 414 good for honda 125cc motorcycle

I only watched this for the food and metallica

Use a dash cover. A guy that collects vintage trucks, told me to use a use a cloth soaked with transmission fluid and put onto the entire dash plastic twice a year. it does not need to be dripping wet, but apply it so it has a sheen to the dash. He had cars from the 50's that the plastic dash looked new because he did this to them. I do this twice a year, but wash down the dash first with soap and water, when it dries, then do this application.

The review is not very good because he simply doesn't know the difference in specifics between the machine. It's clear he did not do any homework before shooting the video. Don't waste your time watching it.

My vents up there are in perfect condition and I own a 02

you need to move your camera faster

Igot one and I like it...get familiar with the machine is the point..For the purpose it works for me, it's not a bad machine..

Thank you! Great tip. Much appreciated

How did you get the sun visor reinstalled? I’m working on my 2004 gmc sierra . It’s a pain trying to the holes line back up.

Turbo failure?

Hang up on hangers while taking a hot shower to get the wrinkles out

Hello, by chance do you have photos or video of the part where you remove the block since it is not visible in the video, I have the same problem on the same sprayer, I hope you can help me, excellent video

Why does everyone suck their teeth while speaking now? So annoying.