Video

Smooth Sailing Boat 🤩

For those who know how to live!

Perfect boat... Just needs a four burner stove top.

Nice

howmuch isit ?

This is the perfect cruising yacht!!! No flybridge means less air draft means negligible side wind effects. Oh I can dream can't I

Stunning, with natural wood finishes (not glossy) a nice mix of modern and vintage optics. Seakeeper stabilizer a plus. Enjoyed the video!

What about the engine room ?

when it comes to toughness how is it compared to Targa from finland? is there any information on the toughness of the GRP

What model is this???

No Sliding doors.

This was an amazing video. Such an inspiration!

If you are considering a yacht of this type and length you must look at this builder. Incredible in my opinion.

Well, I guess if you don't have much else, I reckon this will do...

Wow, just stumbled on this. Many memories with them both! Enjoyed working with Roger during my 2 years at Sabre. My first day I started working on tooling for a new 28’ hull mold. Then on to the 34’ hull and deck/cockpit molds. Thought I would never finish the plug for that cockpit! I worked throughout the facility inside and out, you name it I think I did it. Roger was a mentor! I learned a lot from him. Was fortunate to sail with them on occasion. I then went on to build and repair/refinish boats from 8’ to 50’ over the next 35 years @ North Shore Yachts in Sebago.

Glen!!!! Finally! I'm the owner of S-28 sail #13 (lucky Thirteen" we call her). You were indispensable to me in the last 10 years !!!!!!! Sabre Yachts - This guy is absolutely priceless to EVERY owner of a Sabre sailboat. He ALWAYS gets back to us and has the EXACTLY the right answer...

I love the Sabre except for the aft leaning windshield. So I'm still leaning toward the Sargo.

Rather have a 55 ft power catamaran...

This company just keeps getting better and better. Way to go Sabre!

It mentions the sea keeper. But only for at anchor or tied up at the dock. I thought that its purpose was to stabilize the boat under way and could also be used at rest if you didn't mind the noise.

Just finished commissioning hull #3 few weeks back in WA. wonderful model! Great work! 👍

Promo*SM

I think I have found it. Exept powder coat > stainless or chrome etc....FLIR? Light bar? Too much wood. However, I do concur , that every million it just gets mo and mo betta upto abhout 6 mil

I work at a Sabre/BC dealership in the PNW, so I’m on the commissioning side of Sabres and I can tell you first hand they are really well built! Wires nicely labeled everything was thoughtfully installed with future technicians in mind. So thank you for that! Also our contact with the factory has always been good. Glenn C. is great to call when we have questions. Proud to work on them too!

This is an absolutely beautiful video! Thank you.

Whaoooooo.

Best wishes to both of you.

3.6 mil for this vessel. I was on one at Di Milo. Beautiful boat.

Too bad it is Volvo Penta powered...

I realize this post is dated but I have a 48SE and am looking to put a washer/dryer down in the Utility room. Wondering what brand washer and dryer is recommended. The opening to get a combo unit or separate units down the stairs seems super tight and I'd expect to maybe partially dismantle the washer/dryer. Also, 240V preferred??

Oh, just make sailboats again, will ya?

What is the price oh this magnificent vessel. With the cost of realestate this makes sense! A covered slip is only $600. And electric is $100. I can go fishing for dinner. I can live full-time at the Marina! What’s it going to cost. I already have a price on the 43 Ranger Tug.

I work for Back Cove, the sister company of Sabre Yachts. This video should make all of us proud. Beautifully done!

Way to go Ret!!

Looks like a tremendously rewarding place to work.

Did I understand correctly that your hulls are cored? Even below the waterline? If so, any feedback from owners regarding delimitation and or water ingress? Thx.

Great little video, love the Maine coast. How have the pod drives performed for you, do you find they’re a maintenance drain?

I started working on Sabre 28's on the hull platform doing trim work in the 1980's. It was the beginning of a wonderful life long career in the sailing industry. Probably the finest place to work in the entire state of Maine. Roger Hewson was a great leader and a mentor. I cannot thank Sabre enough for taking great care of me and my family for many ,many years. (Rob Noll/ Dawntreader/ Stargate Earthship Compound Taos, N.M.)

Awesome place to work!❤️🇺🇸⚓️

My grandfather owned a sabar 28 for 30 years now owns a sabar 34 we just found his old 28 now in process of purchasing her back and doin full refit

AMAZING A PIECE OF HEAVEN ON EARTH SINCERELY YOUR'S CHARLETNEWTON

Magic voice, captain! Like a Roger Taylor!))

How much?

This is what I want. The 58 galley up layout is awful in my opinion

Nice

Great boat… but worst music ever

Beautiful boat very expensive to operate and maintain.

One of the best places to work in the USA. After looking back at my career in the yachting business, my years at Sabre were the most rewarding. It's modern, well managed with good pay and benefits.

I have a Sabre 28 hull # 13 (built in 1972), and its better than most sailboats built in the 1990s...

This is wonderful