Video

@@pawel42560 hmmm to be honest, I have no clue :(

@@dominichernandez8087 hey hey Dominic, I also saw that the balancing shafts of the oil sump need to be in sync as well but luckly mine works fine. I intend anyways to rebuild the engine completly soon, therefore I prefered to jump that step and see what's happening. So far so good

​@@thecurlyfixingguy7077Thanks for your answer. I have another question, when applying torque to the crankshaft bolt, did you have the locking pin inserted? I ask because I have read that it cannot resist much torque or it will break. Thanks again!

@@dominichernandez8087 yes sir, otherwise you'll rotate your crankshaft. Basically I let the blocking pin inserted from begging all the way till the end before I did the final 2 complete rotations and made sure it goes back in its place easily, this way confirming the alignment of the timing

@@thecurlyfixingguy7077 Thanks for your answer! I would like to ask you something about fuel efficiency (If you happen to know), I have already replaced spark plugs (NGK), replaced the air filter, cleaned fuel injectors, cleaned MAF sensor and I'm getting about 6km/L, my car is a 320i and there is definitely something failing. I also don't have oxygen sensor related errors to believe something is wrong with them. Would you know if there is something else I would have to check?

@@dominichernandez8087 oooououou, 6km/L that would be aprox 16 L/100km... That's huge, I have 10km/L and mine is a 1.8. what about the engine power? Is all ok when hitting that throttle pedal? I only have in mind the fuel filter (that you didn't mentioned replacing). Other than that I would recommend a diagnosis for deeper look into cars performance :-? But let us know if the fuel filter was the issue (but this would affect dramatically the performance of the car)

You have bad idling?

Salut domnule. Hmmmm, pot fi multe motive, dacă ai urmat toți pașii de blocare și strângere a distribuției, aș recomanda o diagnoză să vezi ce erori citește computerul

Hello, if the coolant level is ok and you don't have air in the cooling system, I would first check engine oil level and age (how old is the oil) & make sure the oil pump works properly; then I would think about running too lean mixture (too much air thru the carburetor) but this should also influence the engine behavior when running it - this can be checked by looking at your spark plug color ( A spark plug that is running too lean will have a light tan or grayish color). Hmmm, my brain at 6:46 am stops here. Let me know if any of the suggestions helped and if not, let's find out somehow together. Keeping my fingers crossed for you

@@thecurlyfixingguy7077 thank you very much for your answer.

Pfff, to be honest, I can't tell

Yes sir, so you can screw back in the hand brake shaft and then be able to press the calliper piston inside

Salut, dacă schimbi și lanțul care angrenează roțile dințate din baia de ulei, da, ai nevoie de acel blocator.eu nu l-am schimbat deci n-am avut nevoie. Anul ăsta îmi propun să refac motorul complet și voi ataca și acel subiect

Hello sir, you can remove only the left "big" pannel but don't forget about the underneath plastic mountings

@@thecurlyfixingguy7077 Thank you for the clarification!

@@oychoppa anytime

thank you sir for the feedback. no, I had no leaks from the replaced gasket anymore. I am planning to rebuild the engine this summer because it's still "eating oil" and has some visible leak points. So stay tuned for I'll make a series out of it. Peace

Hello hello, thank you! To be honest I will guess it's at least similar if not identical procedure

Yes, that's a bit tricky. From my point of view you should try wiggle the civer while putting it back. Be patient and make sure everything is well seated before you tight the bolts

@@thecurlyfixingguy7077 thank you, I actually found a new trick, I basically removed the wipers and the covers around the wiper arm controller as if I want to replace it, it gave a lot of space and just made everything so much easier, if only I had figured out this trick long ago, fitting this gasket would be an hour job from start to end 😆

@@Driftkingmo fantastic!! Thank you very much for the idea! Apreciate it. Wish you many km without any heavy repairs

Salut domnule, din ce am citit pe site-ul ăsta: www.neorom.ro/ghid-uleiuri (Recunosc că nu cunoșteam detalii despre normele de uleiuri recomandate de producător), Volvo recomandă normele A1/3 sau B3/4. Totuși, uleiul folosit în video a fost comandat pe baza talonului (VIN) de la dealer de piese deci nu mă aștept să fie probleme cu el. Oricum îți mulțumesc frumos pentru remarcă, am mai învățat ceva nou și o să fiu atent la acest aspect în viitor pentru a prelungi cât mai mult viața motoarelor.

Hello hello, hmmmm :-? It could be multiple reasons. I would recomend a diagnoze. But make sure you've put back the ignition coils strongly connected. That's just one thing that comes to my mind now. Other thing, spark plugs age :-?. But anyways, keep us posted, would apreciate it

@@thecurlyfixingguy7077 spark plugs are done a few weeks ago, after we started the car it went into limp mode . Do we have to reset the valvetronic motor? If yes how???

@@SpherePK to be honest I never did that but if you say limp mode, then I totally recomend a diagnose and that should narrow down your problem

Liked your video, very informative. The only thing is the music you input between talking is way too loud. I had to volume ++ then volume - - - - - and replay video few times

@@amberg3382 thank you very much for this helpful feedback! I apreciate it. I will try to invest more and more in equipment and editing so that videos will get easier and enjoyable to watch

Hello. Actually not really. I've replaced it because I bought a second hand wheel hub and the bearing was rusty so it was mandatory to change it. But to diagnose a "broken"/tired wheel bearing, you should hear a whizzing sound when you turn to the oposite direction of the broken bearing wheel (if you turn right and you hear that whizzing sound, that means that either your front or back left bearing is bad - usually is obvious). There is also other diagnose method, like lifting the car and shake the wheel from upper to lower part and feel if there is any "play" while doing that. Let me know if this was helpful

Așa este, ai dreptate. Îți doresc baftă maximă cu distribuția. După ce mă întorc din concediu în iulie, mă apuc de refăcut motorul complet :) o să bag și aici pe canal video-uri cu procesul de "rebuild"

Salut vanosurile alea au o catare anume conteaza cum le pui ?

@@patriciaparvuica1329 solenoidele nu neapărat. Dar te cam restrictioneaza cuplele cablurilor să le pui în aceeași poziție. Dacă este vorba de "roțile" de pe axele cu came, da, acelea au poziție fixă explicat la minutul 2:46

Ce părere aveți despre acest motor am achiziționat recent

Respect your comment, thank you! what could have I done better?

Hey dear Thomas, I would guess you'll need to unlug the fuel lines, disconnect any electrical cable (like fuel level sensor) and then undo the bolt holding the buttom of the fuel tank on the frame. Best would be if you can find a service/owners manual and there you should have the procedure well described. Peace

ps. girlfriends nails 10/10

Oioi, I'm Onut Robert Eduard on Facebook, dm there please

@@thecurlyfixingguy7077 the turbo is the problem, consume the oil:))))))

@@claudiubostiog710 dude, I'm afraid I don't understand you :-?

exactly what i was going to ask!!!!!!! i want to do this and i was thinking i could mesure my old one to figure out and then when i pulled it out its was so badly destroyed there was no way i could mesure the diamiter of it

Hello to you both, you could use measuring callipers and try the sharp side of them to roughly measure the exterior and interior diameter (but this can only happen for the outter ones). For the interior ones, you'll need to either have the original code for the bushing (which is nearly impossible in case of chinese scooters) either you'll need to tear them appart and then measure them properly and wait for the new ones. We have a market în Timișoara Romania which has a chinese scooter parts store so I guess/hope you should be able to find one around you as well

Hahaha :)))) thank you very much, I'm glad I could help. Wish you all the best from Romania

Tank you very much for the tip, apreciate it

I hope you answer 🤞

Hello hello to you too! pffff unfortunately it wasn't my personal bike and it's near to impossible to find out in the near future what was the dimension of the O-ring. But maybe you can use a caliper to measure the interior of the whole so you can determine the big diameter of the O-ring and then play with some widths until you get the sweet one . Or maybe a full service manual could help? Let me know how you'll deal with it

Hey hey, could you please switch to english?

@@thecurlyfixingguy7077 how many thousands of kilometers can such an engine travel... is it the same as the Honda reflex 250......????

??????

@@user-ym7vv1me8x hello, yes, it's the same engine as the honda Reflex 250. How many km? I cannot say exactly how many because it always depends on how you treat the engine. But if you treat it right, I bet it can go up to 100.000 km, easily. Wish you a great day

Thank you sir!

Hahaha, it wouldn't be a "job" without any challenge