Video

Hi there! After the water is evacuated, just wipe down the shower base or allow it to dry before setting tile. See at 1:23 in the video! Hope that helps!

@@schlutersystems1thank you so much for the guidance. Quick question we bought this product SCHLUTER SYSTEMS Ditra 54-sq ft Polyethylene Waterproofing Tile Membrane Can we use on over cement board than perform water test? Does the water accumulated inside the holes evaporates? Please advise and thank you!

I think it may be best for you to give our Customer Support team a call so you can discuss your project in a bit more detail. Always a little difficult to understand the unique details of a project online... and we want to make sure to steer you in the right direction... 888-472-4588 Shower floors are typically covered in KERDI, not DITRA... but if you are using DITRA there or in another wet area and need to flood test it, you would carefully wet vac any leftover water in the squares with the vacuum on an angle (so it doesn't debond the DITRA from the substrate) and then proceed with the install. Be sure to use an approved substrate in accordance with the handbook, such as the KERDI-SHOWER-TRAY or a mortar bed in the shower or concrete or the appropriate wood substrate (etc.) in other areas. Cement board would not be an approved substrate under DITRA matting.

@@schlutersystems1 thank you so very much for your help and guidance. Blessings

Yes, VARIO can be used in an off-the-wall application.

I have some profiles in my kitchen! Love my -BWA between my countertop and backsplash. So yes, definitely! 🍊

Hi Maverick - I think it may be easier to discuss this together over the phone - our Customer Service team may be able to advise, or they can connect you with your Schluter rep to talk through the options. 888-472-4588 (US) or 800-667-8746 (Canada). Thanks!

The Schluter water test is a 24 hour flood test and should be drained at 24 hours. This is consistent with most building code requirements, however if your local governing building code requirement is for longer than 24 hours, please test accordingly.

Yes there is - starting at 1:37 we state that "the substrate must be clean, even, load bearing, and level" and we show that you use a damp sponge to moisten the wood prior to applying the thin-set. Thanks! 🍊

Yes, the KERDI-LINE-VARIO can be used in a DITRA-HEAT shower application.

Hi Kyle, these -SNLT lighted shower niches are designed for vertical installation only.

Hi Chip, we used ABS glue for connecting the ABS drain to the ABS pipe, but you would use PVC glue to connect a PVC drain to a PVC pipe.

The SHOWERPROFILE-S can be installed on either wall interchangeably. Hope this helps! 🍊

With KERDI waterproofing membrane, the sequence of membrane installation can vary- what's important is that a minimum 2" (50 mm) overlap is maintained at all joints and proper connection to the KERDI-DRAIN is established. It doesn't actually matter which layer of KERDI goes down first in order for a waterproof seal to be made and continue to be water tight. So, although shingle lapping of the KERDI membrane isn't necessary, it is an acceptable option for any shower installation. 🍊

Hi Jeff! Our customer service team would be better suited to answer this question. You can reach them at 888-472-4588 (USA) or 800-667-8746 (Canada). Hope this helps!

@@schlutersystems1 Thanks. I called and they suggested I caulk around the pipes and toilet flange with Kerdi Fix.

Hi there! Our product support team will be able to assist you! You can reach them at 888-472-4588 (US) or 800-667-8746 (CA).

Hi there! The sealer won't affect our shower system! Hope that helps!

The best case is for the curb to be installed directly on the subfloor. If the tile is solid and well adhered to the subfloor, it might be okay, as long as the curb has a solid foundation. But ideally, it's preferred to install it on the cement.

@@schlutersystems1 Thank you!

Yes, KERDI can be applied over any Gypsum wallboard meeting the ASTM C1396/C1396M standard.

If you give our customer service team a call, they can discuss your project with you in a bit more detail and advise on which KERDI-BOARD can be used - or help you find a Schluter dealer near you with more stock. 888-472-4588 Hope this helps!

Hi Joseph! Would be best to contact our product support team: they will be able to assist you! US : 800-472-4588 CA : 800-667-8746

Yes, PVC/plastic or metal can be used. You just have to confirm if you have any local requirements and that you are grounding appropriately for the style/material you choose.

If you are referring to a 3 wire set up, where you have two lines for the 240V power and a third for the "neutral" (that's not needed), you should check your local codes for the proper way to cap that wire off.

@@schlutersystems1 Thank you I am referring to a three wire cable I still do see how you have a complete circuit

If you are referring to a 3 wire set up, where you have two lines for the 240V power and a third for the "neutral" (that's not needed), you should check your local codes for the proper way to cap that wire off.

Hi there! Yes. Follow the applicable Shower handbook detail and discuss trowel size with the tile manufacturer and follow the tips in the following video to make sure you get full coverage. czcams.com/video/AaP1uA6FIQE/video.htmlsi=Fnf5abiW6LBis-4y . Hope that helps!

Hi there! We have another video that shows how to create and finish a niche shelf. Here is the link: czcams.com/video/697IqAYmpnk/video.html Hope that helps!

Hi there! You can install the KERDI membrane over painted walls as long as it is a latex based paint; should be in good condition and the paint can't be peeling off. If you need to make some repairs on your wall with dry wall mud, you will need to apply a latex primer before installation of the shower system. If you are not sure, you can apply PRIMER-U prior to the KERDI. Would be good to get in touch with our Customer Service team as they will be able to guide you all the details of your installation. You can reach them at 888-472-4588 (US) or 800-667-8746 (CA). Hope that helps!

Hi Becky - would you be able to call our Customer Support team to discuss your project in a bit more detail.. they can advise if drilling additional holes in the ring is possible, or suggest a solution depending on your specifics. 888-472-4588 Thanks!

Hi there! For surfaces that appear smooth and flat, we would recommend starting with a 1/4 x 3/8" trowel. However, rougher surfaces may require a larger notch trowel to achieve adequate coverage. Masonry walls are often not perfectly flat, with high and low spots, so you should probably start with something a little larger. Also, the walls should be checked with a straight edge before installing KERDI-BOARD and finished tile. Please don't hesitate to call our Support team if you want to discuss your specific project in more detail. 888-472-4588. Thanks!

Hi there! We have a few drain options, here’s the scoop: The KERDI-DRAIN bonding flange is available in ABS, PVC, or stainless steel. And the grate is available in stainless steel or anodized aluminum. The KERDI-LINE linear drain is available in stainless steel. KERDI-LINE-VARIO and KERDI-DRAIN-F bonding flanges are made of polypropylene and come with both an ABS and a PVC coupling. You can check out all the drain options on our website - just type in the name of the drain in the Search bar in the top right hand corner: www.schluter.com/schluter-us/en_US/

Hi Chri, that may be a possibility... but it would be best to discuss your project first in much more detail to be sure you get the right advice. Are you able to contact your Schluter rep? Or you can also contact our customer service team. US: 888-472-4588 Canada: 800-667-8746 Also, here's a video showing how to cut the pipe in the floor -- that may be a possibility - but your rep or customer service would be best suited to discuss with you and advise. czcams.com/video/o33UqcV7gSs/video.htmlsi=yhaPnTdEdZdMFNRt

Hi there! Yes, you can follow the same handbook directions for installing KERDI above a tub surround. bit.ly/46jgEkV

Hi Jerome! Would you be able to reach out to our product support team? A live conversation would be the best approach. This way, we can discuss the specifics of your project in detail and provide you with the most accurate and tailored recommendations. You can contact them at 888-472-4588 (US) or 800-667-8746 (CA).

Hi there! Thin-set mortar is the only option to be used to apply these waterproofing components. KERDI-FIX is not suitable.

Hi Luke! The KERDI-LINE-VARIO does not have any ends in the channel body. It doesn't need any. Because it's meant to be shortened, it is easier to just trim down the channel and install it as is. The KERDI membrane will provide the waterproofing in the small area at the ends and the open end will be hidden by the tile, so no worries. Hope that helps!

Glad to hear the video helped! Let us know how it goes!